Get a quote now
Blog 2026-10-19

DEUTZ Cylinder Head Part Numbers: 1013 and 2012 Series Chart

DEUTZ Cylinder Head Part Numbers: BF4M1013, BF6M1013, BF4M2012, BF6M2012

A customer sends a photograph of a DEUTZ cylinder head, writes “BF4M2012, please quote”, and waits. That message is not enough to price the part, and it is not the customer’s fault. Between the four model names that get used most often in this family there are two different bore sizes, two cylinder counts, two valve configurations, and at least two ways to buy the same casting: bare, or complete with the valve train already fitted.

We cast and machine these heads. This page sets out what actually separates them, which part numbers we can defend with more than one source, and where the catalogues disagree with each other. Where the evidence is thin we say so rather than filling the gap with a number that looks confident.

Table of Contents

What the Four Model Names Actually Describe

The four names that arrive in most DEUTZ cylinder head inquiries are not four comparable products. They are the four corners of a two-by-two grid.

DEUTZ cylinder heads from the 1013 and 2012 families

The first number after the M is the cylinder count. The four digits after that are the engine platform, not a year and not a power rating. So BF4M1013 means four cylinders on the 1013 platform, and BF6M2012 means six cylinders on the 2012 platform. The B means turbocharged and the F means the engine is a high-speed four-stroke; neither letter changes the casting.

Model Cylinders Bore x stroke Displacement Valves per cylinder Total valves Head type
BF4M1013 4 108 x 130 mm 4.76 L 2 8 One-piece, all four cylinders
BF6M1013 6 108 x 130 mm 7.15 L 2 12 One-piece, all six cylinders
BF4M2012 4 101 x 126 mm 4.04 L 2 8 One-piece, all four cylinders
BF6M2012 6 101 x 126 mm 6.06 L 2 12 One-piece, all six cylinders

Two things fall out of that table immediately, and both of them cause failed orders.

The bore is different. 1013 engines run 108 mm bores, 2012 engines run 101 mm. A head that spans six 108 mm bores cannot seal six 101 mm bores, and no amount of gasket compound will change that. These are different castings from different patterns.

The length is different. A four-cylinder head and a six-cylinder head from the same platform share the bore spacing, the port layout and the valve train design, but the six-cylinder head is two combustion chambers longer. They are not interchangeable and they are not the same price.

One Piece of Cast Iron, Not Six

This is worth stating plainly because published descriptions of these engines contradict each other on it.

Technical write-ups of the BF6M1013EC describe the head as a block-type cylinder head where a single casting spans all six cylinders. So does the write-up of the TCD 2012 L04 2V. Against that, at least one European trading site advertises the same engine family as having single-cylinder heads, which would mean one head per cylinder.

The photographs settle it. The image below is a four-cylinder 2012 head, viewed from the top. Count the valve spring retainers along the top face.

DEUTZ BF4M2012 cylinder head with eight valve springs visible on the top face

There are eight of them, on one casting. Four cylinders, two valves each, one head. The same part viewed from the side shows the same eight springs and the injector bore between them.

DEUTZ BF4M2012 cylinder head, side view showing the valve springs and injector bore

The six-cylinder version behaves the same way, with twelve springs on one casting.

This matters commercially. If you have been told these engines use one head per cylinder and you order six heads for a six-cylinder BF6M2012, you have ordered six times what the engine needs. If you order one head for a Cummins K19 on the same assumption, you have ordered one sixth of what the engine needs. The two conventions exist in the same market and they are not interchangeable.

There is a direct comparison in our earlier article on the Cummins K19, K38 and K50 cylinder head 3811985, where one engine genuinely does need six separate heads.

Rows of finished six-cylinder DEUTZ heads on the shop floor before packing

DEUTZ Cylinder Head Part Numbers

The table below separates what we can support with more than one independent source from what appears in only one place. The evidence column is the important one. A number that appears on a single supplier page and nowhere else is a lead, not a fact.

Part number Fits Description Evidence
04255259 BF4M1013 Cylinder head Two sources, consistent
04258234 BF6M1013 Cylinder head, approximate weight 67.4 kg Two sources, consistent
04285994 BF4M2012, TD4L2012, TCD2012 Bare cylinder head, without valve train Four sources, consistent on fitment
04297766 TCD2012 L04 2V Complete cylinder head assembly with valves One source only
04290630 BF4M2012 Cylinder head, variant not stated One source only
4256805 BF4M2012 Cylinder head, variant not stated One source only
4259554 BF6M2012 Cylinder head One source only
04202239 BF4M1013 Cylinder head, older number One source only
04205358 BF4M1013 Cylinder head, older number One source only
04207694 BF4M1013 Cylinder head, older number One source only
04255949 BF4M1013 Cylinder head, older number One source only
04255291 BF4M1013 Cylinder head, older number One source only
04255293 BF4M1013 Cylinder head, older number One source only

The number 04285994 also cross-references to 714003AT on at least one catalogue. We have not been able to confirm what that number belongs to, so we do not quote it as an equivalent.

Two observations about the shape of this list.

The 1013 family carries a long tail of older numbers in the 0420 range. Six of them appear together on one Chinese parts catalogue under a single heading, all described as four-cylinder 1013 heads. That is consistent with a casting that has been revised repeatedly over a long production life, where each revision got a new number and the old numbers stayed in circulation. We list them because customers arrive holding them, not because we can independently confirm each one.

The 2012 family is messier in a different way. The same four-cylinder 2012 head is offered by different suppliers under 04285994, 04290630 and 4256805. At least part of that spread is explained in the next section.

DEUTZ BF4M1013 cylinder head, eight valve springs on a four-cylinder casting

Bare Head and Complete Assembly Are Two Different Numbers

This is the single most useful thing on this page if you are buying.

One supplier’s overhaul list for the TCD 2012 L04 2V engine gives two entries side by side. The first is 04297766, described as a cylinder head assembly for the four-cylinder two-valve engine. The second is 04285994, described as a bare cylinder head that excludes the valve components.

Two numbers, one casting, two very different shipments. The assembly arrives with valves, springs, retainers and seats fitted and tested. The bare head arrives as machined cast iron, and your workshop transfers the valve train across, which means new guides and seats if the old ones are worn, and a pressure test afterwards.

That difference shows up in three places at once: the price, the weight, and the lead time. It also explains why quotations for “a BF4M2012 head” from different suppliers can sit far apart without either supplier being dishonest. They may be quoting different things.

When we quote one of these, we state which of the two we are quoting. If a quotation you have received does not say, that is the first question to ask.

DEUTZ cylinder head assembly with the valve train fitted

2V and 4V Heads Do Not Interchange

The 2012 platform was built in two valve configurations, and the model name often does not tell you which one you have.

The TCD 2012 L04 exists as a 2V version with two valves per cylinder, eight valves across four cylinders, and as a 4V version with four valves per cylinder, sixteen valves across four cylinders. A European parts specialist states the position without hedging: a 2V cylinder head will not fit the 4V version, because they differ in porting, number of valves and valve train.

The practical consequence is that the valves, springs, rocker gear and injector arrangement from one will not serve the other, and the gasket is different too. If you order a head for a 4V engine and receive a 2V casting, you will find out at the point of assembly, not at the point of delivery.

Fire deck of a four-cylinder DEUTZ cylinder head showing sixteen valve seats

The photograph above shows the fire deck of a four-cylinder head with sixteen valve seats, four per cylinder. That is a 4V casting. Compare it with the eight-spring head earlier on this page and the difference is visible from across the workshop.

Counting Valve Springs Beats Reading the Nameplate

If you have the head in front of you and you are not certain what it is, do not start with the nameplate. Start with a count.

What you can count What it tells you
8 valve springs on one casting Four cylinders, two valves per cylinder
12 valve springs on one casting Six cylinders, two valves per cylinder
16 valve seats on the fire deck Four cylinders, four valves per cylinder

Then measure the bore spacing or the overall length, and you can separate 1013 from 2012 without a part number at all. The 1013 head is longer for the same cylinder count because the bore spacing is wider.

Six-cylinder DEUTZ BF6M1013 head, twelve valve springs on one casting

The image above is a six-cylinder 1013 head with twelve springs. The image below is the same head from the end, with a stack of finished castings behind it.

End view of a DEUTZ BF6M2012 cylinder head with finished castings stacked behind

Why 1013 and 2012 Heads Never Swap

Three numbers decide this, and they are all in the table at the top of the page.

The bore is 108 mm on the 1013 platform and 101 mm on the 2012. The stroke is 130 mm against 126 mm. The displacement per cylinder is roughly 1.19 litres against 1.01 litres. Everything downstream of those numbers changes with them, including the combustion chamber volume, the fire deck layout and the head bolt pattern.

The heads are also cast from different patterns and machined on different fixtures. In practice this means a 1013 head cannot be made to fit a 2012 block by any means available to a workshop, and the reverse is equally true.

DEUTZ six-cylinder cylinder block on the machining line

We machine the matching DEUTZ cylinder block on the same site, which is how we know how unforgiving the joint is. The block below is a six-cylinder casting with the liners in place.

DEUTZ six-cylinder cylinder block with liners fitted

Weight, Packing and the Freight Quote

Cylinder heads are priced by the piece and freighted by the kilogram, so the weight matters twice.

We have four published weights for the same 04285994 bare head: 35 kg from a European used-parts dealer, 41.5 kg from a Chinese supplier, 45 kg from another Chinese supplier, and 115.0 lb, which is about 52 kg, from a North American dealer listing it as a genuine DEUTZ part.

That is a 17 kg spread on one part number. Some of it is condition, since the 35 kg figure comes from a used unit. Some of it is probably whether the figure includes the valve train, and some is likely packing. We do not have a single authoritative weight, so we do not publish one. We weigh the actual shipment and quote freight on that.

For the six-cylinder 1013 head the position is simpler: one supplier gives 67.4 kg for 04258234, and no second figure has turned up to contradict it. Treat it as approximate.

Practical packing notes, from shipping these:

  • A four-cylinder head ships comfortably in a crate on its own. A six-cylinder head does not, and needs a crate built around it.
  • The machined fire deck must not rest on anything. We block under the ends and brace the sides.
  • Bare heads and complete assemblies do not go in the same crate without separation, because a loose valve in transit will mark a machined face.
  • For sea freight, add desiccant. A cast iron head in a container through a humid season will rust on the fire deck and the customer will reject it on arrival.

How to Confirm Before You Order

Five pieces of information will get you a firm quotation instead of a range. We ask for all five and we would rather ask than guess.

  1. The engine nameplate, photographed, including the full model string and the serial number. The suffix letters matter: BF4M2012, BF4M2012C and TCD2012 L04 2V are not the same build.
  2. Whether the engine is 2V or 4V, if the nameplate does not say. A photograph of the rocker cover removed answers it.
  3. Whether you want a bare head or a complete assembly with the valve train fitted.
  4. Any part number on the old head, photographed where it is legible. If the casting marks are only mould and batch numbers, we will tell you so rather than pretending they are part numbers.
  5. Quantity per engine and how many engines you are rebuilding, so the price reflects the whole order.

Send those to us with the machine model and the country of destination, and we will come back with a price on FOB Qingdao terms, with the head type and valve configuration written into the quotation so there is no ambiguity later.

DEUTZ BF6M1013 cylinder head on the shop floor, with finished heads stacked behind

DEUTZ BF6M2012 cylinder head, top face

DEUTZ BF4M1013 cylinder head, side view

FAQ

Is 04285994 a complete cylinder head or a bare head

Bare. At least one overhaul parts list distinguishes 04285994 as the bare cylinder head without valve components, and lists 04297766 separately as the complete assembly for the TCD 2012 L04 2V engine. Four independent sources agree that 04285994 fits BF4M2012, TD4L2012 and TCD2012 engines.

Can I fit a 4V head on a 2V engine

No. The two versions differ in porting, valve count and valve train, and a parts specialist states directly that a 2V head will not fit the 4V version. The gaskets differ as well.

How many cylinder heads does a DEUTZ BF6M2012 need

One. The 2012 and 1013 families use a single block-type casting that spans all cylinders, so a six-cylinder engine takes one head with twelve valves. This is the opposite of the Cummins K19, which takes six separate heads, one per cylinder.

Will a BF4M1013 head fit a BF4M2012 engine

No. The 1013 platform uses a 108 mm bore and the 2012 platform uses 101 mm, and the head castings come from different patterns. The bore spacing and overall length differ even at the same cylinder count.

What is the weight of a DEUTZ cylinder head

Published figures conflict. For the bare 04285994 head we found 35 kg, 41.5 kg, 45 kg and approximately 52 kg from four different suppliers. For the six-cylinder 04258234 head one source gives 67.4 kg. We weigh each shipment and quote freight on the actual weight.

How do I tell a four-cylinder head from a six-cylinder head

Count the valve springs. Eight springs means four cylinders with two valves each. Twelve springs means six cylinders with two valves each. Sixteen valve seats on the fire deck means four cylinders with four valves each.

Do you machine these heads yourselves

Yes. We are an IATF 16949 foundry and machine shop, and the heads and blocks in these photographs were cast and machined on our own lines. We also work from customer drawings where the original number is no longer available.

What is the minimum order and the delivery term

We quote from one piece for a trial order and price down from there. Terms are FOB Qingdao unless you ask otherwise. Send the engine model, the head type and the quantity to Irene at [email protected] or +86 199 53662121, and include a photograph of the nameplate if you have one.


Ask for a quotation with the engine nameplate and we will tell you which head you actually need, rather than which head the number suggests. Send the details to Irene at [email protected], WhatsApp +86 199 53662121, or use the quotation form. Changwei International, FOB Qingdao.