Get a quote now
Blog 2026-10-16

Timing Gear Housing Part Numbers: Weichai and Sinotruk Chart

Timing Gear Housing Part Numbers: Weichai 6126000 Series and Sinotruk AZ and VZ Codes

A timing gear housing is cheap compared with the engine behind it, so workshops rarely argue about its price. What they argue about is which one to order. Two housings sit side by side on the bench, they weigh within a kilogram of each other, and only one of them will let the camshaft gear mesh at the right centre distance.

If your symptom is an oil leak or a knock, that is a different conversation and we cover it in our timing gear housing diagnosis guide. This page is about the number. Where it is cast, what each digit group means, and which numbers people mix up when they order.

Everything below comes from three places: the Weichai aftermarket service page for timing gear housings, the Sinotruk factory parts price list, and our own workshop photographs of parts we machine. Where a number has only one source, the table says so. We do not fill a gap with a guess.

Table of Contents

  1. A housing number is not a size
  2. How a Weichai 6126000 number is built
  3. Weichai timing gear housing part numbers
  4. How a Sinotruk number is built: AZ, VZ, VG and 6126
  5. Sinotruk timing gear housing part numbers
  6. The numbers that get confused
  7. Where the number is cast on the part
  8. Fitting data from the Weichai service page
  9. FAQ
  10. Send your part number for a quote

A Housing Number Is Not a Size

On a flywheel you can talk about diameter, teeth and bolt holes, and those three numbers narrow the field fast. A timing gear housing does not work that way. It is not a round part, so there is no single diameter to quote. You could measure the distance between the crankshaft bore and the camshaft bore, or the fuel pump gear centre, or the height of the front face, but every workshop measures a slightly different pair of features, and none of those measurements alone picks out one housing.

That is why this part is bought by number, not by dimension. The number is stamped or cast into the housing itself, it is listed in the engine maker’s own parts catalogue, and it does not change when someone measures the wrong face.

There is one more reason to work from the number. A timing gear housing is not a wear item, so the only reason to change one is failure or a rebuild. In both cases the old housing is in your hand when you order, which means the number is in your hand too. There is no need to guess.

How a Weichai 6126000 Number Is Built

Weichai’s older twelve-digit numbers all begin 6126000. The useful part is what comes after. Look at the eighth digit.

On every timing gear housing number in this article, the eighth digit is 1. On every flywheel number for the same engines, the eighth digit is 2.

That is not a coincidence and it is not a guess. Compare these two lines:

  • 6126000 1 1783 — timing gear housing, WP10 and WP12
  • 6126000 1 0932 — timing gear housing, WD615
  • 6126000 2 0208 — flywheel ring gear, WP10, 136 teeth
  • 6126000 2 0211 — flywheel, WD615 and WP10

The 1 group is the front-end gear train: the housing, the timing gears, the housing covers and end plates. The 2 group is the flywheel and the driveline behind it. A part in one group will not turn up in the other.

The trailing letters are revision levels, not options. 61260001194B is the B revision of the 1194 housing. 61260001958A is the A revision of the 1958 housing. A letter at the end means an earlier version of that same number exists, and the two are not always interchangeable, because revisions to this part are usually about the sealing face and the dowel pin position.

Weichai also runs a newer ten-digit series on later platforms, but timing gear housings for WD615, WP10 and WP12 stayed in the twelve-digit 6126000 system, which is convenient: one format covers the whole family you are likely to be asked about.

Weichai Timing Gear Housing Part Numbers

The table lists the housings we build for the Weichai platforms. The last column tells you how strong the evidence is, because not every number is documented to the same depth and we would rather you knew that before you order.

Part number Engine platform Vehicles in service Evidence
612600011783 WP10, WP12 HOWO, Shacman, Foton Auman, concrete mixer trucks Multiple independent suppliers plus our own cast sample
612600010932 WD615 (Euro II and Euro III) HOWO, Yutong buses Multiple suppliers plus our own cast sample, number cast on the part
612600013254 Listed as WP10, WP12 and WD618 by different suppliers Shacman Delong, HOWO, Foton Auman Multiple suppliers, but they disagree on the engine platform
612600011918 WD615 Construction machinery: XCMG, LiuGong, Lonking, Shantui Multiple suppliers, all listing the same machinery applications
612600012122 WP10.5, WP12 Sinotruk, Foton Auman EST Multiple suppliers
61260001194B WD615, Euro III HOWO, Steyr King Our production list only, no independent catalogue entry found

Read that last line again, because it is the honest one. The 1194B housing is a part we machine and ship, and the photo below is the part itself, but we could not find it in a public parts catalogue. If a supplier tells you they have a full catalogue cross-reference for every number they sell, ask them which source. Most of them are copying each other.

Weichai timing gear housing for WD615, machined front face with camshaft and fuel pump bores

The WD615 housing is the busiest of the family. The large bore is the camshaft bore, the smaller round bore is the fuel pump drive gear, and the rectangular opening at the lower left is for the injection pump drive. The bolt pattern around the outside edge is what holds it against the cylinder block, and it is the feature that changes between a Euro II and a Euro IV housing even when the outline looks the same.

Weichai 612600011783 timing gear housing, painted, with part number cast into the front face

The 11783 housing, used on the later WP10 and WP12 platforms, has a wider and shallower camshaft bore housing and a taller front face. If you put it beside the WD615 part the difference is visible from a metre away. If you only have one of them on the bench, it is not.

Weichai timing gear housings for WP10 stacked on the shop floor, machined faces coated with anti-rust primer

The reddish faces above are anti-rust primer on the machined surface, not rust. Housings leave us in batches, and a shipping lot is what the pallet in the photograph is part of. A single unit photographed for a catalogue listing rarely shows you what the parts look like after a month in a container, so we photograph the batch.

Weichai 612600012122 timing gear housing, fully machined face for the WP10.5 platform

The 12122 part is the WP10.5 and WP12 housing. Notice how much more of the front face is machined flat compared with the WD615 part: on the later engines the fuel pump and air compressor have moved, and the housing picked up a wider sealing face to match.

Weichai 612600013254 timing gear housing, part number cast on the lower left of the face

The 13254 housing is the one where suppliers disagree most. We will come back to it in the confusion table, because it is the clearest example of a number that has been copied across platforms without anyone checking.

How a Sinotruk Number Is Built: AZ, VZ, VG and 6126

Sinotruk is where part numbers get genuinely confusing, and the reason is that the same part can carry more than one number depending on which system you are reading.

Four prefixes turn up on the front end of a HOWO engine:

  • AZ is the Sinotruk internal part number system. Front-end housings live in the AZ15000109xx range.
  • VZ is a second Sinotruk series. We have a housing on the floor cast VZ1567010009.
  • VG covers brackets and covers, for example VG1095060006 and VG1095060009, which are gear housing brackets rather than the housing itself.
  • 6126 is the Weichai shared number. Because the same engine family was built under both names, a Sinotruk part can also appear with a Weichai number.

The Sinotruk factory parts price list is the document to work from, because it lists the number, the part name and the price in one line. Three consecutive entries matter here:

Catalogue line Part number Name in the catalogue
A AZ1500010012 Flywheel housing
B AZ1500010932 Gear housing
C AZ1500010933 Timing gear housing

Lines B and C sit next to each other in the catalogue, carry the same price, and differ by one digit at the end. One is called a gear housing and the other a timing gear housing. In Chinese parts lists these two words are often used for the same casting, and in this case they are not the same casting.

Sinotruk HOWO timing gear housing, part number VZ1567010009 cast into the boss on the upper face

The number in the photograph is cast into the raised boss at the top of the housing, next to the camshaft bore. That boss is the first place to look when you have a HOWO housing in your hand and no invoice.

Sinotruk Timing Gear Housing Part Numbers

Part number Name Application Evidence
AZ1500010933 Timing gear housing Sinotruk HOWO, WD615 series, Euro II and Euro III Sinotruk factory price list plus our own cast sample
AZ1500010932 Gear housing Sinotruk HOWO Sinotruk factory price list
AZ1038010009 Timing gear housing, electronic injection engines HOWO Multiple suppliers
61557010008 Timing gear housing HOWO, WD615, single and twin air compressor versions Multiple suppliers
61557010008A Timing gear housing, revised HOWO Multiple suppliers
VZ1567010009 Housing cast with this number HOWO Our own cast sample, no public catalogue entry found

Sinotruk HOWO timing gear housing, machined face with camshaft bore and fuel pump opening

The 10933 housing has the part number cast into the green-painted upper face, and the machined front face carries the camshaft bore at the upper left, the fuel pump bore at the centre right, and the crankshaft opening at the bottom. The green paint is the factory primer, not a customer colour.

Sinotruk timing gear housings stacked after machining, green primer on the unmachined surfaces

Sinotruk timing gear housing, cylinder block side, showing the reinforcing ribs and oil galleries

The rear face is the side that tells you whether the housing has been distorted. The webs between the bores are thin on purpose, and if the part has been overheated or dropped the flat face will not sit flush against the block any more. That is a mechanical check, not a visual one, but the photograph shows where to put a straight edge.

The Numbers That Get Confused

These are the mix-ups we see in real enquiries, with the reason each one happens.

AZ1500010932 against AZ1500010933

One digit at the end, same price in the factory list, adjacent lines in the catalogue, and two names that are used loosely for the same casting. If a customer sends the number 150001093 and stops there, we have to ask which of the two they mean, because the answer changes the part.

AZ1038010009 against Weichai 612600010009

These look like they could be related, and they are not. The AZ number is a Sinotruk internal number, the 6126 number is from the Weichai series. Both are real parts. Neither is a substitute for the other.

A catalogue listing that calls a gear housing a flywheel housing

At least one export listing describes AZ1500010933 as a rear flywheel housing and quotes a weight in the 85 to 90 kg range. A gear housing for this engine family weighs a fraction of that. When a listing is generated by copying a template, the part name and the weight can both belong to a different product. Check the weight against the part you are holding.

612600013254, listed against four different engine platforms

Supply listings for this housing mention WP10, WP12, WD618 and WD618CNG, and one quotes a weight of 21.1 kg while another type of listing puts the same part far lighter. The engine platform tells you which gear train the housing must clear, so four different platforms cannot all be right. Treat any listing that names more than one platform for a housing with suspicion.

A letter at the end is a revision, not an option

61557010008A and 61557010008 are two revisions of one number, and 61260001194B carries its own B revision. The revised part usually has a different sealing face or dowel position. Fitting a revised housing against an older block can leave the gasket face short of contact, which is where the leak starts.

Where the Number Is Cast on the Part

Two of the photographs in this article show a real part number cast into the casting, not a hand mark and not a batch code:

  • 612600010932 on the Weichai WD615 housing
  • VZ1567010009 on the Sinotruk HOWO housing

Weichai 612600010932 timing gear housing, part number cast clearly into the front face

The number sits on the raised pad in the middle of the uncut casting, between the camshaft bore and the fuel pump opening. That pad exists for the number, and the number is put there so that it survives machining.

Two cautions, because we have been burned by this ourselves.

First, not every digit string on a casting is a part number. Castings also carry mould numbers, heat numbers and date codes. We have read housings where the most prominent string on the face turned out to be a mould identifier that appears in no catalogue anywhere. If a number does not resolve, that is usually why.

Second, workshop marks are not part numbers either. The housing below has a strip of masking tape with a hand-written code across the middle of the machined face.

Weichai timing gear housing, cylinder block side, with a hand-written workshop tag across the machined face

P4A is what one of our machinists wrote to track the batch through the shop. It never leaves our building and it means nothing to a customer. When you photograph a housing to send us, ignore the tape.

The practical rule is simple. Photograph the whole front face, photograph the whole rear face, and photograph any raised pad that carries a cast number, close enough that the digits fill the frame. That is three photographs and it is enough for us to identify almost any housing.

Fitting Data From the Weichai Service Page

Weichai publishes service notes for this part on its aftermarket site, and they are worth repeating because three of the four points are the ones people skip.

  • Clean the mating face on the cylinder block completely, then apply anaerobic sealant evenly across it before the housing goes on.
  • Inspect the seal ring for cuts before fitting. Lubricate it, then press it fully into its groove. A ring that is three quarters home will leak.
  • When you fit the oil pump gear and the camshaft gear, line the timing marks on the gears up with the mark on the housing. The mark on the housing is the reference, not the mark on the flywheel.
  • Tighten the housing bolts in a diagonal cross pattern, in stages, to 44 to 58 Nm.
  • To remove the housing, take out the fixing bolts, then withdraw the intermediate gear shaft and the oil pump intermediate shaft before pulling the housing off.

The torque figure is the one we get asked for most often, and 44 to 58 Nm is the range Weichai publishes for the housing bolts themselves. Do not read that across to the fuel pump flange or the cover plate, which have their own values.

FAQ

Is 612600011783 the same as 612600010932?

No. Both are timing gear housings and both belong to the 6126000 1 group, but 11783 is the later WP10 and WP12 housing and 10932 is the WD615 housing. The camshaft bore surround and the front face height differ, and the sealing face does not line up if you swap them.

Can a WD615 housing be fitted to a WP10 engine?

Not directly. The two engine families look similar at the front end, and several suppliers list one housing against both, but the bore spacing and the cover bolt pattern changed between them. If a listing shows one number for both platforms, ask for a photograph of the actual part.

What does the letter at the end of the number mean?

It is a revision level. 61260001194B is the B revision of the 1194 housing and 61557010008A is the A revision of the 61557010008 housing. Revisions to this part are normally about the sealing face or the dowel pin position. Fit the revision that matches the engine you are repairing.

How do I find the part number on a HOWO gear housing?

Look at the raised boss on the upper face, next to the camshaft bore. On the housing in our photograph the number VZ1567010009 is cast into that boss. If the boss is unpainted and the digits are shallow, a photograph taken at a low angle with a side light will pick them out better than a straight-on shot.

Is the number on the casting always the part number?

No. Castings also carry mould numbers, heat numbers and date codes, and some of those are more prominent than the real number. A cast number is only useful once it resolves to a catalogue entry. If it does not resolve, it is probably a mould or batch identifier.

Do you supply these housings by part number or by drawing?

Both. If you have the number we work from that. If you have a worn housing with no readable number, send the three photographs described above and we will match it against what we build. For non-standard front ends we can also work from a customer drawing, which is how several of the housings in this article started.

Do you machine the housing after casting, or ship it as cast?

Every housing in this article is fully machined: the front face, the bores, the sealing face and the bolt holes. A cast-only housing cannot hold the bore positions a gear train needs, so an as-cast housing is not something we offer for this part.

What is the minimum order and the lead time?

Fifty pieces per number for a standard production run, with a twenty-piece trial order available on most numbers. Stock numbers ship in seven to ten days and a fresh production run takes twenty to thirty days. We ship FOB Qingdao in wooden cases.

Send Your Part Number for a Quote

If you are working on a Weichai or Sinotruk front end and you have the number, send it and we will come back with the housing, the price and the lead time. If you have the old housing and no readable number, send the front face, the rear face and the boss, and we will identify it from the casting.

Email Irene at [email protected] or message +86 19953662121 on WhatsApp and WeChat. We are in Changyi, Weifang, Shandong and we ship FOB Qingdao. Standard quotations come back with photographs of the actual part and the packing we use.

Related parts we build for the same engines: gear rooms and timing gear housings, flywheel housings and SAE flange sizes, ring gears, and Weichai flywheels. Mixed containers are available if you are ordering more than one product line.

For a quotation on any of the parts above, use our quote request page.