{
    "id": 2152,
    "date": "2026-11-09T06:44:58",
    "date_gmt": "2026-11-08T22:44:58",
    "guid": {
        "rendered": "https:\/\/www.changweiintl.com\/en\/?post_type=ccm_blog&#038;p=2152"
    },
    "modified": "2026-11-12T17:38:58",
    "modified_gmt": "2026-11-12T09:38:58",
    "slug": "cylinder-head-deck-flatness-reading-it-before-you-machine",
    "status": "publish",
    "type": "ccm_blog",
    "link": "https:\/\/www.changweiintl.com\/zh_cn\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine",
    "title": {
        "rendered": "Cylinder Head Deck Flatness: Reading It Before You Machine"
    },
    "content": {
        "rendered": "<div class=\"wrap\">\n<p>A bare cylinder head that reaches a machine shop almost never reads flat. Put a heavy straight edge across the deck and a 0.10 mm feeler will slip under the middle of a casting that has never been bolted to an engine. The obvious conclusion is that the head is warped and needs a cut.<\/p>\n<p>Detroit Diesel gives a different answer in the Series 60 service manual. The head is machined while clamped in a fixture on its locating surfaces. When the clamps come off, the casting returns to the shape it had before machining. It stays that way until it is bolted and torqued to the block. The manual calls this natural warp, and states that natural warpage is not a cause for correction.<\/p>\n<p>That sentence changes how a deck should be read. It is also the reason this article starts with the fixture rather than with the limits.<\/p>\n<h2 id=\"table-of-contents\">Table of Contents<\/h2>\n<ol>\n<li><a href=\"#what-the-deck-face-has-to-seal\">What the Deck Face Has to Seal<\/a><\/li>\n<li><a href=\"#the-casting-is-machined-while-clamped\">The Casting Is Machined While Clamped<\/a><\/li>\n<li><a href=\"#two-directions-two-limits\">Two Directions, Two Limits<\/a><\/li>\n<li><a href=\"#the-numbers-by-engine-family\">The Numbers by Engine Family<\/a><\/li>\n<li><a href=\"#flatness-alone-never-condemns-a-head\">Flatness Alone Never Condemns a Head<\/a><\/li>\n<li><a href=\"#valve-recession-after-a-cut\">Valve Recession After a Cut<\/a><\/li>\n<li><a href=\"#the-pressure-test-two-protocols-two-verdicts\">The Pressure Test: Two Protocols, Two Verdicts<\/a><\/li>\n<li><a href=\"#when-a-head-can-be-machined\">When a Head Can Be Machined<\/a><\/li>\n<li><a href=\"#what-to-ask-before-you-buy-a-bare-head\">What to Ask Before You Buy a Bare Head<\/a><\/li>\n<li><a href=\"#questions-buyers-ask\">Questions Buyers Ask<\/a><\/li>\n<li><a href=\"#sources-and-evidence-level\">Sources and Evidence Level<\/a><\/li>\n<\/ol>\n<h2 id=\"what-the-deck-face-has-to-seal\">What the Deck Face Has to Seal<\/h2>\n<p>The deck face does one job and it has to do it three ways at once.<\/p>\n<p>It seals combustion pressure at every cylinder, and that pressure is the highest load anywhere on the part. It seals coolant passages that run within a few millimetres of the fire ring. It seals oil returns that must not reach the coolant. A head gasket is a thin part asked to hold three different fluids apart while the casting above it expands and contracts.<\/p>\n<p>That is why a deck is not judged on smoothness. A polished face that is 0.2 mm low in the middle leaks at the fire ring, and a face that is geometrically flat but pitted under the fire ring leaks in the same place. Flatness is one condition of several, and the other conditions are visible only on a close look.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Combustion deck of a six cylinder head with two valve seats per cylinder, injector bores, coolant holes and a machined band around the edge\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-head-deck-face-six-cylinder.jpg\" \/><\/p>\n<p>The deck above shows the two features that decide most arguments. The valve seats sit in the machined area. The coolant holes sit beside them, often within the width of the fire ring. A deck that has corroded around those holes can be flat and still fail a pressure test.<\/p>\n<h2 id=\"the-casting-is-machined-while-clamped\">The Casting Is Machined While Clamped<\/h2>\n<p>A cylinder head is long, thin walled and full of passages. It is not rigid. When it is unbolted from a block it relaxes, and the relaxation is not evenly distributed along its length.<\/p>\n<p>Detroit Diesel describes the sequence in plain terms. The longitudinal warp is normalized at the time of manufacture by clamping the casting in a fixture on its locating surfaces during machining. Unclamped, the casting resumes its original shape. Bolted and tightened to the block, it goes back to the machined shape.<\/p>\n<p>The practical result is that the head on your bench and the head in service are two different shapes, and both are real.<\/p>\n<p>Detroit does not stop there. The same section still sets a limit on the unclamped deck, and the limit is generous in one direction and tight in the other. The number already absorbs the amount of natural warp the process is expected to produce. A head that exceeds it has moved beyond what the fixture accounts for.<\/p>\n<p>The method matters as much as the number. Detroit specifies a heavy accurate straight edge with feeler gauges, five longitudinal stations and twelve transverse stations marked A to L. The reason for twelve is simple. A deck can be straight at one station and bowed at the next, and a single reading down the centre line will miss it.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Combustion deck of a four cylinder head with valves installed, showing the machined flat band and the cast recesses between the ports\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-head-deck-face-four-cylinder.jpg\" \/><\/p>\n<p>The deck above is complete, with valves in place. What a straight edge sees here is the machined band, not the valve heads. Any measurement taken across the valve heads describes the valve job, not the deck.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"End face of an assembled cylinder head with valve springs visible above the casting\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-head-end-face-portrait.jpg\" \/><\/p>\n<p>The end view is worth having for one reason. It shows how little material sits between the deck and the first water passage. That distance is what a cut removes from.<\/p>\n<h2 id=\"two-directions-two-limits\">Two Directions, Two Limits<\/h2>\n<p>Detroit gives 0.279 mm front to rear and 0.076 mm side to side on the Series 60. The longitudinal limit is almost four times the transverse one, and that ratio is not an accident.<\/p>\n<p>Along the length, the head spans every cylinder in a row. Warp accumulates over that span, and the gasket has to keep six fire rings separate. Across the width, the span is short and the gasket band is narrow, so there is little room to absorb a gap. The tight direction is the short one.<\/p>\n<p>The same pattern appears in the Cummins documents, with different numbers and a warning attached. Cummins measures across the combustion face and across the entire head surface as separate readings rather than as one figure.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Close view of two valve heads in their seats on a machined deck, with a cast recess and a coolant hole beside them\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-head-deck-valve-seat-close-up.jpg\" \/><\/p>\n<p>At this distance the difference between a machined surface and a cast surface is obvious. It is also where pitting shows first, at the edge of the machined band where coolant sits.<\/p>\n<h2 id=\"the-numbers-by-engine-family\">The Numbers by Engine Family<\/h2>\n<table>\n<thead>\n<tr>\n<th>Engine family<\/th>\n<th>Document<\/th>\n<th>Limit<\/th>\n<th>Where it is measured<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Cummins ISX15 CM2350<\/td>\n<td>Service manual 002-004<\/td>\n<td>0.15 mm<\/td>\n<td>A to A and B to B corner to corner, C to C across the combustion face<\/td>\n<\/tr>\n<tr>\n<td>Cummins ISX11.9 CM2250<\/td>\n<td>Service manual 002-004<\/td>\n<td>0.200 mm<\/td>\n<td>AA and BB<\/td>\n<\/tr>\n<tr>\n<td>Cummins ISX11.9 CM2250<\/td>\n<td>Service manual 002-004<\/td>\n<td>0.076 mm<\/td>\n<td>CC across the combustion face<\/td>\n<\/tr>\n<tr>\n<td>Cummins ISX11.9 CM2250<\/td>\n<td>Service manual 002-004<\/td>\n<td>0.127 mm<\/td>\n<td>DD across the entire head surface<\/td>\n<\/tr>\n<tr>\n<td>Detroit Series 60<\/td>\n<td>Service manual 1.2.3.3<\/td>\n<td>0.279 mm<\/td>\n<td>front to rear, unclamped<\/td>\n<\/tr>\n<tr>\n<td>Detroit Series 60<\/td>\n<td>Service manual 1.2.3.3<\/td>\n<td>0.076 mm<\/td>\n<td>side to side, unclamped<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Read the first two Cummins rows together and a trap appears. The letter C to C carries 0.15 mm in the ISX15 document and 0.076 mm in the ISX11.9 document. The letters describe the same idea and carry different values, because the two heads are different castings.<\/p>\n<p>This is the most common error we see in incoming inspection sheets. A buyer copies a limit from one manual onto another engine, and the head is then judged against a number that never applied to it.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Top deck of a six cylinder head with valve springs and the cam carrier surface machined flat\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-head-top-deck-valve-springs.jpg\" \/><\/p>\n<p>The top deck has its own flatness callout on most engines, and it is rarely the one that fails. The deck that matters for the gasket is the one facing the block.<\/p>\n<h2 id=\"flatness-alone-never-condemns-a-head\">Flatness Alone Never Condemns a Head<\/h2>\n<p>Cummins states the rule for the ISX15 without ambiguity. If the cylinder head is pitted, grooved, or not within specifications, it must be replaced.<\/p>\n<p>Three conditions, one verdict. Flatness is listed last, and the two visual conditions are listed first. A head can pass the straight edge and still be scrap.<\/p>\n<p>Pitting under the fire ring is the one that catches buyers. It appears as a ring of small craters where the gasket fire ring has been fretting against the deck, or as corrosion at the edge of a coolant hole. Neither can be machined out without removing more material than the head allows.<\/p>\n<p>Grooving runs the other way. A groove is a scratch deep enough to hold a fingernail, usually from a previous gasket failure or from a scraper. A shallow one can be removed with the deck cut. A deep one cannot, because the cut that removes it also removes the material the head needs.<\/p>\n<p>Cracks are the third verdict and the least negotiable. The usual locations are between the valve seats and across the fire deck between cylinders. Detroit is direct about the outcome. If a cracked cylinder head is detected, the cylinder head is replaced.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Bare cylinder head on a pallet with the combustion deck facing the camera, showing valve seat bores and coolant holes\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-deck-holes.jpg\" \/><\/p>\n<h2 id=\"valve-recession-after-a-cut\">Valve Recession After a Cut<\/h2>\n<p>Valve recession is the depth of the valve head below the deck. It is a small number, it moves in the wrong direction when the deck is cut, and it has a limit that changed mid production.<\/p>\n<table>\n<thead>\n<tr>\n<th>Engine family<\/th>\n<th>Recession when new<\/th>\n<th>Maximum in service<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Cummins ISX11.9 CM2250, intake<\/td>\n<td>1.003 to 1.384 mm<\/td>\n<td>3.05 mm<\/td>\n<\/tr>\n<tr>\n<td>Cummins ISX11.9 CM2250, exhaust<\/td>\n<td>0.953 to 1.334 mm<\/td>\n<td>3.05 mm<\/td>\n<\/tr>\n<tr>\n<td>Cummins ISM, heads built before 21 August 2006<\/td>\n<td>0.76 to 1.17 mm<\/td>\n<td>3.05 mm<\/td>\n<\/tr>\n<tr>\n<td>Cummins ISM, heads built after 21 August 2006 with scalloped seat<\/td>\n<td>0.51 to 0.92 mm<\/td>\n<td>2.80 mm<\/td>\n<\/tr>\n<tr>\n<td>Detroit Series 60<\/td>\n<td>valve heads recessed at least 1.4 to 1.8 mm<\/td>\n<td>not stated in the same section<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>The ISM split is a good reminder that a model year is not a specification. The same engine family was built with two seat designs, and the second one sits the valve closer to the deck. A head judged against the older numbers passes when it should not.<\/p>\n<p>There is a second direction to this. Cutting the deck reduces recession, because the deck comes down toward the valve. A head that was already at the low end of the range can go under the minimum after a light cut, which brings the valve closer to the piston. That is one of the reasons a machined head has to be measured again rather than assumed good.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Three rows of six cylinder heads on a pallet, the front row showing valve springs and the rear rows showing bare castings\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-heads-assembled-on-pallet.jpg\" \/><\/p>\n<h2 id=\"the-pressure-test-two-protocols-two-verdicts\">The Pressure Test: Two Protocols, Two Verdicts<\/h2>\n<p>A pressure test finds what a straight edge cannot. Porosity in the casting, a crack that has not opened yet, a leaking injector tube. Two manufacturers test the same kind of part in two different ways.<\/p>\n<table>\n<thead>\n<tr>\n<th>Item<\/th>\n<th>Cummins ISX11.9 CM2250<\/th>\n<th>Detroit Series 60<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Air pressure<\/td>\n<td>138 kPa, 20 psi<\/td>\n<td>207 kPa, 30 psi<\/td>\n<\/tr>\n<tr>\n<td>Water bath temperature<\/td>\n<td>60 C<\/td>\n<td>82 to 93 C<\/td>\n<\/tr>\n<tr>\n<td>Minimum time in the bath<\/td>\n<td>not stated in the summary<\/td>\n<td>20 minutes<\/td>\n<\/tr>\n<tr>\n<td>Verdict if bubbles come from the casting or the injector cup area<\/td>\n<td>replace the head<\/td>\n<td>replace the head<\/td>\n<\/tr>\n<tr>\n<td>Verdict if bubbles come from a serviceable component such as a cup plug<\/td>\n<td>the head can be repaired<\/td>\n<td>injector tube replaced<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>The two protocols differ by fifty percent in pressure and by more than twenty kelvin in bath temperature. A test run at the lower pressure in a cold tank can pass a leak that the stricter test would find. If a supplier reports a pressure test, the pressure and the bath temperature belong in the report alongside the result.<\/p>\n<p>Cummins adds one caution that is easy to skip. Do not pressure test the head with the valves and valve springs installed. Water that enters cannot be dried out thoroughly and will damage the guides and stems. Detroit solves the same problem from the other side, fitting dummy injectors so the injector bores are sealed during the test.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Bare six cylinder head standing on a pallet, front face toward the camera with threaded ports and a large coolant opening\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-front-view.jpg\" \/><\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Bare six cylinder head without valves resting on a pallet, cam carrier side up\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-on-pallet.jpg\" \/><\/p>\n<h2 id=\"when-a-head-can-be-machined\">When a Head Can Be Machined<\/h2>\n<p>Machining a deck is normal maintenance, and like every maintenance operation it has a limit.<\/p>\n<p>Trade references put the Detroit allowance at 0.020 inch on four cycle heads, which is 0.508 mm, with a combined head and block allowance of 0.030 inch. The figure is quoted in secondary sources rather than in the manual section above, so treat it as practice rather than as a published specification. Evidence level: single source, secondary.<\/p>\n<p>0.508 mm is a familiar number on this site. It is the same figure the Detroit 50 series manual gives for resurfacing a flywheel friction face, printed as 0.020 inch. The two parts are unrelated, but the number comes from the same engineering habit: allow one cut, not a series of cuts.<\/p>\n<p>The reasons a head cannot always be cut are geometry, not stubbornness.<\/p>\n<p>On an overhead cam engine with a chain or belt, lowering the head retards valve timing, and the retardation shifts the torque curve upward. On a gear driven camshaft the effect is worse. The gears converge as the centre distance closes, and eventually they jam.<\/p>\n<p>Some engines have no allowance at all. The Navistar 6.9 litre head is quoted at 4.795 to 4.805 inch between the fire deck and the valve cover rail, a band so narrow that manufacturing tolerance consumes it. Others, including the 9.0 litre Navistar and the Volkswagen 1.6 litre diesel, are described as not resurfaceable within factory guidelines.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Side face of a cylinder head with valve springs along the top edge and cored ports below\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-head-side-face-portrait.jpg\" \/><\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Bare six cylinder head seen from above with the cam carrier machined surfaces and injector bores\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-cam-carrier.jpg\" \/><\/p>\n<p>A last point on sequence. When injector tubes are replaced, the work is done after the deck is cut, and it is followed by a pressure test. Doing it the other way round means cutting into a surface that was just sealed.<\/p>\n<h2 id=\"what-to-ask-before-you-buy-a-bare-head\">What to Ask Before You Buy a Bare Head<\/h2>\n<p>A bare head is bought on a photograph and a promise unless the order asks for more. Six items close most of the gap.<\/p>\n<ol>\n<li>A deck photograph with a straight edge on it. One image, taken square to the deck, with the feeler visible. It proves the check happened.<\/li>\n<li>The flatness figure with the instrument named. A number without the tool is not comparable to your own reading.<\/li>\n<li>The pressure test report, with pressure and bath temperature. A result without those two values cannot be reproduced.<\/li>\n<li>Valve recession at every valve, not an average. One valve out of range condemns the seat work.<\/li>\n<li>The build code or casting date. On the Cummins ISM the seat design changed on a date, and the date decides which recession limit applies.<\/li>\n<li>Whether the head has been machined before, and by how much. A second cut on a head that has already been cut is where the allowance disappears.<\/li>\n<\/ol>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Three rows of bare and assembled six cylinder heads lined up on a pallet in a workshop\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-heads-three-rows-workshop.jpg\" \/><\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Six cylinder block standing on a granite surface plate with a height gauge beside it\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/cylinder-block-on-surface-plate.jpg\" \/><\/p>\n<p>The photograph above is the reason we ask for a plate. A deck measured on a wooden pallet, on a truck bed, or on the floor of a container is a reading of the support, not of the part. A granite plate and a height gauge remove that variable before the first number is written down.<\/p>\n<h2 id=\"questions-buyers-ask\">Questions Buyers Ask<\/h2>\n<h3 id=\"why-does-a-head-read-warped-off-the-engine-but-seal-fine-in-service\">Why does a head read warped off the engine but seal fine in service<\/h3>\n<p>Because the casting is machined while clamped. The unclamped shape includes natural warp, and bolting the head to the block pulls it back to the machined shape. A reading taken on a bare casting describes the free state, which is the state Detroit and Cummins both measure, and both allow for.<\/p>\n<h3 id=\"can-a-0-15-mm-warp-be-machined-out\">Can a 0.15 mm warp be machined out<\/h3>\n<p>Sometimes, and the decision does not belong to the warp alone. If the deck is pitted or grooved, or if the cut would take the head below its minimum thickness, the answer is no. Cummins states the verdict for the ISX15 directly: pitted, grooved, or out of specification means replacement.<\/p>\n<h3 id=\"is-the-flatness-limit-the-same-across-cummins-engines\">Is the flatness limit the same across Cummins engines<\/h3>\n<p>No. The ISX15 document gives 0.15 mm for A to A, B to B and C to C. The ISX11.9 document gives 0.200 mm for AA and BB, 0.076 mm for CC and 0.127 mm for DD. The letters look alike and the values do not.<\/p>\n<h3 id=\"do-i-need-a-pressure-test-if-the-deck-measures-flat\">Do I need a pressure test if the deck measures flat<\/h3>\n<p>Yes. Flatness describes the sealing surface. A pressure test describes the casting behind it. A head with porosity in a water jacket can be perfectly flat and still fill a cylinder with coolant.<\/p>\n<h3 id=\"how-much-valve-recession-is-too-much\">How much valve recession is too much<\/h3>\n<p>Cummins gives 3.05 mm as the maximum operational recession on the ISX11.9 and on earlier ISM heads, and 2.80 mm on ISM heads built after 21 August 2006 with a scalloped seat. The installed figure when new is far smaller, between 0.5 and 1.4 mm depending on the valve and the engine.<\/p>\n<h3 id=\"does-resurfacing-a-head-change-the-engine-timing\">Does resurfacing a head change the engine timing<\/h3>\n<p>On an overhead cam engine driven by a chain or a belt, yes. Lowering the head retards cam timing. On a gear driven camshaft the gears converge, and the limit is mechanical rather than thermal.<\/p>\n<h2 id=\"sources-and-evidence-level\">Sources and Evidence Level<\/h2>\n<table>\n<thead>\n<tr>\n<th>Claim<\/th>\n<th>Source<\/th>\n<th>Level<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Head is machined clamped, natural warp is not a cause for correction<\/td>\n<td>Detroit Series 60 service manual, section 1.2.3.3<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Unclamped limits 0.279 mm front to rear, 0.076 mm side to side<\/td>\n<td>Detroit Series 60 service manual, section 1.2.3.3<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Five longitudinal and twelve transverse measuring stations<\/td>\n<td>Detroit Series 60 service manual, section 1.2.3.3<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Pressure test 207 kPa, 82 to 93 C, 20 minutes minimum<\/td>\n<td>Detroit Series 60 service manual, section 1.2.3.2<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Valve heads recessed 1.4 to 1.8 mm<\/td>\n<td>Detroit Series 60 service manual, section 1.2.3.4<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Flatness 0.15 mm, replace if pitted, grooved or out of specification<\/td>\n<td>Cummins ISX15 CM2350 service manual 002-004<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Flatness 0.200, 0.076 and 0.127 mm by direction<\/td>\n<td>Cummins ISX11.9 CM2250 service manual 002-004<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Recession limits and 3.05 mm maximum operational<\/td>\n<td>Cummins ISX11.9 CM2250 service manual 002-004<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Pressure test 138 kPa at 60 C, repair or replace by source of bubbles<\/td>\n<td>Cummins ISX11.9 CM2250 service manual 002-004<\/td>\n<td>primary, manual text<\/td>\n<\/tr>\n<tr>\n<td>Recession limits change by build date on the ISM<\/td>\n<td>Cummins technical service bulletin, 2008<\/td>\n<td>primary, bulletin<\/td>\n<\/tr>\n<tr>\n<td>Detroit allowance 0.020 inch, head plus block 0.030 inch<\/td>\n<td>trade technical reference, secondary<\/td>\n<td>single source, secondary<\/td>\n<\/tr>\n<tr>\n<td>Some engines cannot be resurfaced within factory guidelines<\/td>\n<td>trade technical reference, secondary<\/td>\n<td>single source, secondary<\/td>\n<\/tr>\n<tr>\n<td>Head photographs<\/td>\n<td>our own production and packing area<\/td>\n<td>primary, first hand<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Two honesty notes. The heads in the photographs are from our own production and packing area, and none of them is the specific engine named in the limit tables. And the casting number on the head in the wide deck photograph was not legible at the magnification we could produce, so we have not printed it.<\/p>\n<h2 id=\"send-the-deck-photo\">Send the Deck Photo<\/h2>\n<p>If a head is in dispute, three images settle most of it: the deck with a straight edge on it, the same deck at an angle that shows the fire ring band, and the pressure test setup with the gauge readable.<\/p>\n<p>Browse the range on the <a href=\"https:\/\/www.changweiintl.com\/en\/product\">product overview<\/a>, compare the machining limits on a related casting in <a href=\"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-resurfacing-limits-how-much-can-be-machined\">flywheel resurfacing limits<\/a>, or send your drawing and your inspection sheet to the <a href=\"https:\/\/www.changweiintl.com\/en\/quote\">quotation desk<\/a>.<\/p>\n<p>We reply with the deck reading we can hold, the instrument we will use to prove it, and the points we still need to confirm.<\/p>\n<\/div>\n<p><!-- cw-schema:begin --><br \/>\n<script type=\"application\/ld+json\">{\"@context\":\"https:\/\/schema.org\",\"@type\":\"BlogPosting\",\"headline\":\"Cylinder Head Deck Flatness: Reading It Before You Machine\",\"datePublished\":\"2026-11-09T06:44:58\",\"dateModified\":\"2026-11-09T06:44:58\",\"author\":{\"@type\":\"Organization\",\"name\":\"Changwei Intelligent Equipment\",\"url\":\"https:\/\/www.changweiintl.com\"},\"publisher\":{\"@type\":\"Organization\",\"name\":\"Changwei Intelligent Equipment\",\"url\":\"https:\/\/www.changweiintl.com\",\"logo\":{\"@type\":\"ImageObject\",\"url\":\"https:\/\/www.changweiintl.com\/logo.png\"}},\"mainEntityOfPage\":{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.changweiintl.com\/en\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine\"},\"inLanguage\":\"en\"}<\/script><br \/>\n<!-- cw-schema:end --><\/p>",
        "protected": false
    },
    "excerpt": {
        "rendered": "<p>A cylinder head is machined while clamped in a fixture, so the bare casting springs back when the clamps come off. Detroit and Cummins both publish deck limits anyway. This is what those numbers mean, how the two pressure tests differ, and what to ask for before you buy a bare head.<\/p>",
        "protected": false
    },
    "author": 1,
    "featured_media": 2139,
    "template": "",
    "meta": {
        "_yoast_wpseo_focuskw": "cylinder head deck flatness",
        "_yoast_wpseo_title": "",
        "_yoast_wpseo_metadesc": "",
        "_cw_seo_title_en": "Cylinder Head Deck Flatness: Reading It Before You Machine",
        "_cw_seo_metadesc_en": "A head measured off the engine and a head bolted to the block are two different shapes. Deck limits, the two pressure tests, and when warp is not a fault."
    },
    "ccm_blog_tag": [
        222,
        218,
        219,
        221,
        220
    ],
    "class_list": [
        "post-2152",
        "ccm_blog",
        "type-ccm_blog",
        "status-publish",
        "has-post-thumbnail",
        "hentry"
    ],
    "yoast_head": "<!-- This site is optimized with the Yoast SEO plugin v28.9 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>Cylinder Head Deck Flatness: Reading It Before You Machine &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.changweiintl.com\/zh_cn\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine\/\" \/>\n<meta property=\"og:locale\" content=\"zh_CN\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Cylinder Head Deck Flatness: Reading It Before You Machine &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.\" \/>\n<meta property=\"og:description\" content=\"A cylinder head is machined while clamped in a fixture, so the bare casting springs back when the clamps come off. Detroit and Cummins both publish deck limits anyway. This is what those numbers mean, how the two pressure tests differ, and what to ask for before you buy a bare head.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.changweiintl.com\/zh_cn\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine\/\" \/>\n<meta property=\"og:site_name\" content=\"Weifang Changwei Intelligent Equipment Co., Ltd.\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/profile.php?id=61573276931730\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-12T09:38:58+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-cam-carrier.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"815\" \/>\n\t<meta property=\"og:image:height\" content=\"612\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"\u9884\u8ba1\u9605\u8bfb\u65f6\u95f4\" \/>\n\t<meta name=\"twitter:data1\" content=\"20 \u5206\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/cylinder-head-deck-flatness-reading-it-before-you-machine\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/cylinder-head-deck-flatness-reading-it-before-you-machine\",\"name\":\"Cylinder Head Deck Flatness: Reading It Before You Machine &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/cylinder-head-deck-flatness-reading-it-before-you-machine#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/cylinder-head-deck-flatness-reading-it-before-you-machine#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/bare-cylinder-head-cam-carrier.jpg\",\"datePublished\":\"2026-11-08T22:44:58+00:00\",\"dateModified\":\"2026-11-12T09:38:58+00:00\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/cylinder-head-deck-flatness-reading-it-before-you-machine#breadcrumb\"},\"inLanguage\":\"zh-Hans\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/cylinder-head-deck-flatness-reading-it-before-you-machine\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"zh-Hans\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/cylinder-head-deck-flatness-reading-it-before-you-machine#primaryimage\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/bare-cylinder-head-cam-carrier.jpg\",\"contentUrl\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/bare-cylinder-head-cam-carrier.jpg\",\"width\":815,\"height\":612,\"caption\":\"Bare six cylinder head seen from above with the cam carrier machined surfaces and injector bores\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/cylinder-head-deck-flatness-reading-it-before-you-machine#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"\u9996\u9875\",\"item\":\"https:\\\/\\\/www.changweiintl.com\\\/en\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"\u535a\u5ba2\",\"item\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"Cylinder Head Deck Flatness: Reading It Before You Machine\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#website\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/\",\"name\":\"Weifang Changwei Inteligent Equipment Co, Ltd\",\"description\":\"\u660c\u7ef4\u667a\u80fd\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.changweiintl.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"zh-Hans\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#organization\",\"name\":\"Weifang Changwei Intelligent Equipment Co., Ltd.\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"zh-Hans\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/06\\\/1782266646-favicon-512.png\",\"contentUrl\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/06\\\/1782266646-favicon-512.png\",\"width\":512,\"height\":512,\"caption\":\"Weifang Changwei Inteligent Equipment Co, Ltd\"},\"image\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/profile.php?id=61573276931730\"],\"legalName\":\"Weifang Changwei Intelligent Equipment Co., Ltd.\",\"alternateName\":[\"Changwei\",\"\u6f4d\u574a\u660c\u7ef4\u667a\u80fd\u8bbe\u5907\u6709\u9650\u516c\u53f8\"],\"address\":{\"@type\":\"PostalAddress\",\"streetAddress\":\"Zhicheng World Trade Center, High-Tech Zone\",\"addressLocality\":\"Weifang\",\"addressRegion\":\"Shandong\",\"addressCountry\":\"CN\"},\"contactPoint\":[{\"@type\":\"ContactPoint\",\"contactType\":\"sales\",\"availableLanguage\":[\"en\",\"zh\"],\"email\":\"tony15589697779@gmail.com\",\"telephone\":\"+8615589697779\"}],\"knowsAbout\":[\"engine flywheel\",\"flywheel ring gear\",\"flywheel housing\",\"gear chamber\",\"OEM engine components\",\"IATF 16949 certified manufacturing\"],\"areaServed\":\"Worldwide\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->",
    "yoast_head_json": {
        "title": "Cylinder Head Deck Flatness: Reading It Before You Machine &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.",
        "robots": {
            "index": "index",
            "follow": "follow",
            "max-snippet": "max-snippet:-1",
            "max-image-preview": "max-image-preview:large",
            "max-video-preview": "max-video-preview:-1"
        },
        "canonical": "https:\/\/www.changweiintl.com\/zh_cn\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine\/",
        "og_locale": "zh_CN",
        "og_type": "article",
        "og_title": "Cylinder Head Deck Flatness: Reading It Before You Machine &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.",
        "og_description": "A cylinder head is machined while clamped in a fixture, so the bare casting springs back when the clamps come off. Detroit and Cummins both publish deck limits anyway. This is what those numbers mean, how the two pressure tests differ, and what to ask for before you buy a bare head.",
        "og_url": "https:\/\/www.changweiintl.com\/zh_cn\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine\/",
        "og_site_name": "Weifang Changwei Intelligent Equipment Co., Ltd.",
        "article_publisher": "https:\/\/www.facebook.com\/profile.php?id=61573276931730",
        "article_modified_time": "2026-11-12T09:38:58+00:00",
        "og_image": [
            {
                "width": 815,
                "height": 612,
                "url": "https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-cam-carrier.jpg",
                "type": "image\/jpeg"
            }
        ],
        "twitter_card": "summary_large_image",
        "twitter_misc": {
            "\u9884\u8ba1\u9605\u8bfb\u65f6\u95f4": "20 \u5206"
        },
        "schema": {
            "@context": "https:\/\/schema.org",
            "@graph": [
                {
                    "@type": "WebPage",
                    "@id": "https:\/\/www.changweiintl.com\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine",
                    "url": "https:\/\/www.changweiintl.com\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine",
                    "name": "Cylinder Head Deck Flatness: Reading It Before You Machine &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.",
                    "isPartOf": {
                        "@id": "https:\/\/www.changweiintl.com\/#website"
                    },
                    "primaryImageOfPage": {
                        "@id": "https:\/\/www.changweiintl.com\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine#primaryimage"
                    },
                    "image": {
                        "@id": "https:\/\/www.changweiintl.com\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine#primaryimage"
                    },
                    "thumbnailUrl": "https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-cam-carrier.jpg",
                    "datePublished": "2026-11-08T22:44:58+00:00",
                    "dateModified": "2026-11-12T09:38:58+00:00",
                    "breadcrumb": {
                        "@id": "https:\/\/www.changweiintl.com\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine#breadcrumb"
                    },
                    "inLanguage": "zh-Hans",
                    "potentialAction": [
                        {
                            "@type": "ReadAction",
                            "target": [
                                "https:\/\/www.changweiintl.com\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine"
                            ]
                        }
                    ]
                },
                {
                    "@type": "ImageObject",
                    "inLanguage": "zh-Hans",
                    "@id": "https:\/\/www.changweiintl.com\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine#primaryimage",
                    "url": "https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-cam-carrier.jpg",
                    "contentUrl": "https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/bare-cylinder-head-cam-carrier.jpg",
                    "width": 815,
                    "height": 612,
                    "caption": "Bare six cylinder head seen from above with the cam carrier machined surfaces and injector bores"
                },
                {
                    "@type": "BreadcrumbList",
                    "@id": "https:\/\/www.changweiintl.com\/blog\/cylinder-head-deck-flatness-reading-it-before-you-machine#breadcrumb",
                    "itemListElement": [
                        {
                            "@type": "ListItem",
                            "position": 1,
                            "name": "\u9996\u9875",
                            "item": "https:\/\/www.changweiintl.com\/en\/"
                        },
                        {
                            "@type": "ListItem",
                            "position": 2,
                            "name": "\u535a\u5ba2",
                            "item": "https:\/\/www.changweiintl.com\/blog"
                        },
                        {
                            "@type": "ListItem",
                            "position": 3,
                            "name": "Cylinder Head Deck Flatness: Reading It Before You Machine"
                        }
                    ]
                },
                {
                    "@type": "WebSite",
                    "@id": "https:\/\/www.changweiintl.com\/#website",
                    "url": "https:\/\/www.changweiintl.com\/",
                    "name": "Weifang Changwei Inteligent Equipment Co, Ltd",
                    "description": "\u660c\u7ef4\u667a\u80fd",
                    "publisher": {
                        "@id": "https:\/\/www.changweiintl.com\/#organization"
                    },
                    "potentialAction": [
                        {
                            "@type": "SearchAction",
                            "target": {
                                "@type": "EntryPoint",
                                "urlTemplate": "https:\/\/www.changweiintl.com\/?s={search_term_string}"
                            },
                            "query-input": {
                                "@type": "PropertyValueSpecification",
                                "valueRequired": true,
                                "valueName": "search_term_string"
                            }
                        }
                    ],
                    "inLanguage": "zh-Hans"
                },
                {
                    "@type": "Organization",
                    "@id": "https:\/\/www.changweiintl.com\/#organization",
                    "name": "Weifang Changwei Intelligent Equipment Co., Ltd.",
                    "url": "https:\/\/www.changweiintl.com\/",
                    "logo": {
                        "@type": "ImageObject",
                        "inLanguage": "zh-Hans",
                        "@id": "https:\/\/www.changweiintl.com\/#\/schema\/logo\/image\/",
                        "url": "https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/06\/1782266646-favicon-512.png",
                        "contentUrl": "https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/06\/1782266646-favicon-512.png",
                        "width": 512,
                        "height": 512,
                        "caption": "Weifang Changwei Inteligent Equipment Co, Ltd"
                    },
                    "image": {
                        "@id": "https:\/\/www.changweiintl.com\/#\/schema\/logo\/image\/"
                    },
                    "sameAs": [
                        "https:\/\/www.facebook.com\/profile.php?id=61573276931730"
                    ],
                    "legalName": "Weifang Changwei Intelligent Equipment Co., Ltd.",
                    "alternateName": [
                        "Changwei",
                        "\u6f4d\u574a\u660c\u7ef4\u667a\u80fd\u8bbe\u5907\u6709\u9650\u516c\u53f8"
                    ],
                    "address": {
                        "@type": "PostalAddress",
                        "streetAddress": "Zhicheng World Trade Center, High-Tech Zone",
                        "addressLocality": "Weifang",
                        "addressRegion": "Shandong",
                        "addressCountry": "CN"
                    },
                    "contactPoint": [
                        {
                            "@type": "ContactPoint",
                            "contactType": "sales",
                            "availableLanguage": [
                                "en",
                                "zh"
                            ],
                            "email": "tony15589697779@gmail.com",
                            "telephone": "+8615589697779"
                        }
                    ],
                    "knowsAbout": [
                        "engine flywheel",
                        "flywheel ring gear",
                        "flywheel housing",
                        "gear chamber",
                        "OEM engine components",
                        "IATF 16949 certified manufacturing"
                    ],
                    "areaServed": "Worldwide"
                }
            ]
        }
    },
    "_links": {
        "self": [
            {
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/ccm_blog\/2152",
                "targetHints": {
                    "allow": [
                        "GET"
                    ]
                }
            }
        ],
        "collection": [
            {
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/ccm_blog"
            }
        ],
        "about": [
            {
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/types\/ccm_blog"
            }
        ],
        "author": [
            {
                "embeddable": true,
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/users\/1"
            }
        ],
        "version-history": [
            {
                "count": 3,
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/ccm_blog\/2152\/revisions"
            }
        ],
        "predecessor-version": [
            {
                "id": 2155,
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/ccm_blog\/2152\/revisions\/2155"
            }
        ],
        "wp:featuredmedia": [
            {
                "embeddable": true,
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/media\/2139"
            }
        ],
        "wp:attachment": [
            {
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/media?parent=2152"
            }
        ],
        "wp:term": [
            {
                "taxonomy": "ccm_blog_tag",
                "embeddable": true,
                "href": "https:\/\/www.changweiintl.com\/zh_cn\/wp-json\/wp\/v2\/ccm_blog_tag?post=2152"
            }
        ],
        "curies": [
            {
                "name": "wp",
                "href": "https:\/\/api.w.org\/{rel}",
                "templated": true
            }
        ]
    }
}