立即获取报价
博客 2026-10-30

Deutz Flywheel Part Numbers: 04204260, 04204326, 04282542

Table of Contents

Three Numbers, One Silhouette

A DEUTZ flywheel arrives on a pallet, painted red, with a ring gear shrunk onto the rim and a machined friction face on the other side. Photograph it from either side and it looks like every other DEUTZ flywheel in the same size class. The differences between 04204260, 04204326 and 04282542 are not visible until you know where to look, and none of them are visible from three metres away.

That is the problem this guide is written for. All three numbers are real DEUTZ flywheel part numbers, all three are sold interchangeably by parts traders under the loose label “DEUTZ flywheel”, and at least one published fitment list puts two of them against the same engine family. A buyer who orders by engine model has a coin-flip chance of receiving the right casting.

The three castings in this article were photographed in our own shop, one part at a time, on the same pallet and under the same light. They are not a catalogue render and they are not the same part photographed three times: the ring gear diameters differ, the face drilling differs, and each carries a different eight-digit number etched into the rim. That etched number is the only identification on the part that a buyer can read from a photograph without guessing.

Number Swap number quoted with it Fitment as published Weight as published Evidence grade
04204260 02240193 F4L912, F6L912, F6L913, BF4L913, BF6L913, BF4M1012, BF4M1013, BF4M2012, BF6M1013, BF6M2012, BFM1013, TCD 2012 L04/L06 2V, TCD 2013 L04 not published Two listings, near-identical wording
04204326 02160763 FL912, FL914, BFL913, BFL914, BF4M1012, BF4M1013, BF4M2012, BF6M1013, BF6M2012, TCD 2012 L04/L06 2V, TCD 2013 37.5 kg Two listings
04282542 04259984 TCD 2012 L04 2V and BF6M2012C, named on the same page 40.96 kg One listing

Read the fitment column twice. Two different numbers, 04204260 and 04204326, are both published against the 1013 and 2012 families, and both are published against the air-cooled 912 and 913 families. That overlap is not a typo in one shop’s catalogue; it appears in the listing text of more than one supplier, which tells you something useful and slightly uncomfortable: the engine family alone does not select the flywheel.

What the Rim Etch Says, and What It Does Not

On all three parts the number is etched into the machined band between the ring gear and the friction face. It is a shallow line of characters, roughly 4 mm tall, cut after machining, and it survives paint because it sits on a surface that is not painted.

Close-up of the etched marking XZ-F04204260 PGS21 on the rim of a DEUTZ flywheel

The first part reads XZ-F04204260 PGS21. The second reads XZ-F04204326 PEXA005. The third reads XZ-F04282542 PGN050.

Close-up of the etched marking XZ-F04204326 PEXA005 on the rim of a DEUTZ flywheel

Three parts, three different six-character codes after the number. Whatever those codes mean at the shop that applied them, they change from part to part while the eight digits do not. When you quote a flywheel, quote the eight digits and ignore everything around them.

Close-up of the etched marking XZ-F04282542 PGN050 on the rim of a DEUTZ flywheel

What the etch does not tell you is equally important. Look at the cast face of 04204260: there is a raised rectangular border containing a cast number, sitting between two of the small holes. At the resolution of a normal product photograph it is unreadable, and even enlarged eight times the characters smear into the casting skin. On 04204326 the raised cast number near the ring gear seat reads as a seven or eight digit string that does not match 04204326 at all. Those raised numbers are pattern, mould or batch identifiers. They are not the part number, and a supplier who photographs only the cast face has given you nothing you can verify.

The practical rule is short. Ask for the rim, not the face.

The Number Each Supplier Quotes

The reason these three numbers blur together is visible in the listing text itself. Sellers write the same flywheel three or four ways, and buyers copy whichever form they saw first.

A number such as 04204260 appears as 04204260, as 0420 4260 with a space every four digits, as 0420-4260 with a dash, and as 4204260 with the leading zero dropped. Parts guides for DEUTZ describe exactly this habit: the leading zero, the spacing and any trailing suffix come and go between catalogue, invoice and part, while the digits stay the same. Match the digits, not the punctuation.

That advice has a hard edge. Dropping the leading zero is safe. Dropping or adding a digit is not. One Dalian supplier catalogue lists a flywheel numbered 04284260 on the same page as 04282542, 04204326 and 04254991. 04284260 and 04204260 differ by one digit in the middle and are listed as two different flywheels. We have no photograph of 04284260 and no second source for it, so we treat it as a number to verify rather than a number to quote. If a customer asks for 04284260, the first question is whether they meant 04204260.

The same block of numbers is also not uniformly flywheels. The same catalogue lists 04297773, 04297775 and 04297793 as flywheel housings, not flywheels, in the middle of a run of 0429 numbers that are flywheels. A prefix that looks consistent is not a guarantee of the part type.

Swap Numbers That Travel With These Flywheels

Each of the three flywheels has a second number attached to it in the trade.

Flywheel number Second number How it is presented Evidence grade
04204260 02240193 “Replacement part number” pair, both forms listed on the same product page Two listings, same pairing
04204326 02160763 Listed as “General No.” beside 04204326 Two listings
04282542 04259984 Both numbers in the product title for a TCD 2012 L04 2V application One listing

Both forms of each pair are in circulation. A buyer holding a packing list that says 02240193 and a machine that the dealer’s catalogue calls 04204260 is not looking at a mistake; it is the same flywheel under two numbers. The reverse also happens: a quote comes back with 02240193 when the enquiry said 04204260, and the buyer assumes the supplier substituted a different part.

The 04282542 and 04259984 pair is the weakest of the three in public sources, because we found it on a single page. Treat it as a lead, not as a rule, and ask the supplier to confirm the pairing in writing before it becomes part of your stock record.

What the Photos Actually Show

Photographs settle what catalogues argue about, provided they are taken from the right angle. Here is what the three parts look like side by side.

04204260 from the ring gear side. The small holes in the cast face sit singly, at two different radii, spread around the full circle rather than grouped. The hub carries a ring of bolt holes with one counterbored hole set off the pattern.

Red painted DEUTZ flywheel 04204260 seen from the ring gear side on a plywood pallet

The same part from the clutch side shows two concentric bolt circles around the crankshaft bore, with the inner circle much closer to the bore than on the other two parts.

Machined clutch face of DEUTZ flywheel 04204260 with two concentric bolt circles around the crankshaft bore

The side view is where the ring gear becomes obvious. There is a distinct machined band, a parting line, and then the darker tooth ring: the ring gear is a separate steel ring shrunk onto a cast body, not teeth cut into the casting.

Side view of DEUTZ flywheel 04204260 showing the shrunk-on ring gear and the machined rim band

04204326 from the ring gear side. The difference that matters is in the upper left of the casting: a short row of closely spaced small holes, drilled in a line along one sector, close to the ring gear seat. Neither of the other two parts has that row.

Red painted DEUTZ flywheel 04204326 from the ring gear side with a short row of small holes near the rim

Close-up of the closely spaced row of small holes drilled in the cast face of flywheel 04204326 next to the ring gear seat

Its clutch face is also drilled differently from 04204260: the small holes sit in a tight ring immediately around the hub rather than out on the face.

Machined clutch face of DEUTZ flywheel 04204326 with a ring of small holes close to the crankshaft bore

Side view of DEUTZ flywheel 04204326 showing the ring gear edge and the etched rim band

04282542 is the smallest of the three and the easiest to rule out once it is on a bench. The recess behind the friction face is deeper, and the clutch face carries six large holes on a single bolt circle with nothing else competing for space on that circle.

Machined clutch face of the smaller DEUTZ flywheel 04282542 with six large holes on one bolt circle

Side view of DEUTZ flywheel 04282542 with the ring gear and a deep recess behind the friction face

One caution about that photo set. The front view of 04282542 in our library has a Chinese caption burned into the background, so it is not usable on an English page; the two views above are the clean ones. If you are building your own identification sheet, shoot on a plain background with no overlay text, because an overlay is the first thing that makes a buyer distrust the photo.

Why the Engine Model Is Not Enough

DEUTZ built several generations inside one type code. The 912 and 913 families are air-cooled in-line engines; the 1012, 1013 and 2012 families are water-cooled, and the TCD 2012 and TCD 2013 are the later turbocharged, charge-air-cooled versions with electronic control. Published DEUTZ data for the TCD 2012 gives 101 mm bore and 126 mm stroke for both the four and six cylinder versions, 4.04 litres and 6.06 litres respectively, with rated output of 103 kW and 155 kW at 2400 rpm.

A flywheel does not care about displacement. It cares about the crankshaft flange it bolts to, the clutch it carries, and the starter it has to mesh with. When a manufacturer changes a component inside a series without renaming the engine, the parts catalogue records it in a variant table keyed to the engine serial number, and that is why a BF4M1013 from one year can take a different flywheel from one built in another. The plate on the engine, with its type code and Motor No., is the lookup key. The machine model on the bonnet is not.

That also explains the overlap in the fitment column earlier. When 04204260 and 04204326 are both published against the 1013 family, at least one of those listings is a shorthand that will be wrong for some serial numbers. We are not going to tell you which one is wrong, because we have not seen the DEUTZ variant tables and we will not guess at them. What we can tell you is that the number on the part beats the number on the listing.

How to Send an Enquiry That Lands on the Right Part

Six items turn a flywheel enquiry from a conversation into a quotation.

What to send Why it decides the part
Eight-digit number from the rim etch The only identification on the part that survives paint and matches catalogue data
Engine plate photograph, type code and Motor No. Resolves the variant table entry when two numbers claim the same engine family
Photograph of the ring gear, teeth in focus Confirms the ring gear, which is replaceable and is often the actual failure
Outside diameter across the teeth Separates parts that share a number family but not a size
Clutch cover bolt circle and number of holes Distinguishes drilled faces that look identical at a glance
Quantity and destination port Drives packing, and flywheels ship badly in thin cartons

If the number has been painted over or ground off, say so and send the four measurements instead. A ring gear outside diameter, a clutch bolt circle, a crankshaft bore and a hub depth will identify a flywheel far more reliably than the engine model, and we would rather quote from measurements than from a guess.

Which of the Three We Build

We cast and machine flywheels in ductile and grey iron at our foundry in Changyi, Weifang, and we shrink-fit the starter ring gear in-house. The three parts in this article are in our product library as photographed castings, with the rim etch applied to the eight-digit number.

What we do not do is publish a tooth count we have not counted, a weight we have not put on a scale, or a fitment we have not confirmed. The weight column in the first table is deliberately thin: 37.5 kg and 40.96 kg are single-source figures from one supplier page each, and we would rather weigh your part than repeat someone else’s number. If you need freight calculated before ordering, we will weigh the actual casting and quote from that.

For a part number we have not built before, the route is a drawing or a sample. Flywheel castings are pattern work: the crank flange, the clutch face drilling and the ring gear seat are all fixed by the pattern, and a ring gear change alone does not make a new flywheel number.

The other end of the same engines is covered in our DEUTZ cylinder head part number chart, which follows the same 1013 and 2012 families from the top of the block.

Ring gears themselves are covered separately, including the shrink-fit allowance and the heating limits, on our ring gear page. If your problem is a chewed ring gear on an otherwise sound flywheel, that is a different and much cheaper conversation than a new casting.

FAQ

Are 04204260 and 04204326 the same flywheel?

No. They are two separate DEUTZ numbers with two separate second numbers, 02240193 and 02160763, and the castings in our photographs are drilled differently. Both numbers are published against the 1013 and 2012 engine families by at least one supplier, which is exactly why the engine model cannot be the deciding input.

Which number fits a BF4M1013?

Both 04204260 and 04204326 are published against the 1013 family. We have not seen the DEUTZ variant table that resolves this by serial number, so we will not pick one for you. Send the Motor No. from the engine plate together with the rim etch, and the two together will settle it.

What is 02240193?

It is the second number quoted with 04204260 by two independent listings. If your packing list says 02240193 and the catalogue says 04204260, you are probably holding the same flywheel.

Is 04284260 the same as 04204260?

It is one digit different and one Dalian catalogue lists it as a separate flywheel. We have no photograph of it and no second source. Confirm before you quote it, and check whether the customer meant 04204260.

Can the starter ring gear be replaced without replacing the flywheel?

Yes. The ring gear on all three parts is a separate steel ring shrunk onto the cast body, visible as its own band in the side views. Replacement depends on the ring gear being available as a service part for that flywheel, and on the interference fit being done correctly, not on the flywheel being recast.

Do you supply these three from stock?

We quote per order. Send the number, the quantity and the destination port, and we will confirm lead time in writing. We do not publish stock levels we cannot hold.

Send the eight-digit number from your rim, the engine plate photo and the quantity to our quotation desk. If you only have a photograph of the cast face, send it anyway, and we will tell you what is missing.