Dongfeng Flywheel Part Numbers: 1005115 vs 1005120 vs D5010

Dongfeng DDi and DCi11 Flywheel Part Numbers: 1005115, 1005120 and D5010 Explained
A Dongfeng dealer asks for 1005115-E9500. A workshop in Lagos has the same flywheel on the bench, reads 1005120-E9500 off the casting, and concludes the dealer sent the wrong part. Both numbers are correct. They describe two levels of the same assembly.
This is the single most common mix-up on Dongfeng DDi and DCi11 engines, and it is the reason we photograph the cast-in numbers on every flywheel that leaves our foundry floor.

Table of Contents
- Why One Flywheel Carries Three Part Numbers
- The 1005115 and 1005120 Pair
- The E Code Does Not Follow Engine Displacement
- D5010 Numbers and the Renault Era
- What the Cast-In Marks Actually Prove
- Ordering Checklist
- The Trap Hiding in the Same Prefix at FAW
- Frequently Asked Questions
Why One Flywheel Carries Three Part Numbers
Dongfeng’s commercial vehicle engine line has been renamed twice in fifteen years. The flywheel did not change much, but the numbering did.
There are three numbering systems in circulation today, and all three are still quoted by parts sellers:
- 1005115-Exxxx is the flywheel and ring gear assembly. The starter ring is pressed on and the unit ships as one piece.
- 1005120-Exxxx is the flywheel body. Cast and machined disc, ring gear treated as a separate item.
- D5010xxxxxx is the Renault-era number, still used on DCi11 engines built during the Dongfeng Renault joint venture.
A seller quoting 1005115-E4600 and a catalogue listing 1005120-E4600 are not in conflict. One is quoting the assembly, the other the disc. The price difference between them is roughly the price of a ring gear plus the press fit.
The 1005115 and 1005120 Pair
The pairing is consistent across the whole E family we hold in stock:
| Assembly number | Body number | Engine designation | Note |
|---|---|---|---|
| 1005115-E4200 | 1005120-E4200 | Dongfeng DDi series | Cast number confirmed on our stock |
| 1005115-E4201 | 1005120-E4201 | Dongfeng DDi series, X7 platform | Cast number not read yet |
| 1005115-E4600 | 1005120-E4600 | Longqing DDi75, Tianlong KL | 1005120 described as the body number by trade listings |
| 1005115-E8100 | 1005120-E8100 | Fengshen 4H, Longqing DDi47 | Cast number confirmed on our stock |
| 1005115-E9300 | 1005120-E9300 | Longqing DDi11 | Assembly number confirmed by multiple sellers |
| 1005115-E9500 | 1005120-E9500 | Longqing DDi13, 6306 bearing fitted | Cast number confirmed on our stock |
| 1005115-E1100 | 1005120-E1100 | Fengshen 4H, T30 platform | Both numbers sold side by side |
Two rows in this table matter more than the rest. E4600 and E1100 are the cases where trade listings themselves spell out both numbers in one line, sometimes as 1005115-E4600 flywheel assembly, 1005120-E4600 body number. That is the clearest public confirmation that the pair is one part, two levels.


If a customer sends you 1005120-E9500 and you quote 1005115-E9500, you are quoting a part with the ring gear included. The customer may accept it, or may push back because their account only covers the disc. Ask which one is on the invoice before you ask for a price.
The E Code Does Not Follow Engine Displacement
Buyers routinely assume the four digits after the dash encode displacement. They do not.
| Code | Actual engine | Displacement reality |
|---|---|---|
| E4200 | Dongfeng DDi series | Not 4.2 L |
| E4600 | Longqing DDi75 | 7.5 L class |
| E8100 | Longqing DDi47, Fengshen 4H | 4.7 L class |
| E9300 | Longqing DDi11 | 11 L class |
| E9500 | Longqing DDi13 | 13 L class |
E4600 sits on a 7.5 litre engine while E8100 sits on a 4.7 litre engine. Read the two side by side and the displacement theory collapses immediately.
The correct way to use the E code is as a platform generation marker. It tells you which engine family the flywheel was designed for, not how big the engine is. Confirm the engine designation separately, either from the engine plate or from the vehicle model, and only then confirm the flywheel.

We keep side profiles in our files for exactly this reason. Two flywheels can share a bolt pattern and a diameter and still differ in ring gear width and offset. A face-on photo hides that. A side view does not.

D5010 Numbers and the Renault Era
The DCi11 was the Renault-designed eleven litre engine that Dongfeng built under licence. Its flywheels kept the Renault numbering, and those numbers are still live in the aftermarket.
| Renault number | What it is | Evidence |
|---|---|---|
| D5010330691 | Flywheel and ring gear assembly, 152 teeth | Cast number confirmed on our stock; multiple sellers list 152T |
| D5010330690 | Same family, gear ring assembly | Listed alongside 30691 by the same sellers |
| D5010224693 | DCi11 China 5 flywheel assembly | Multiple sellers, one quotes it as a ring gear assembly |
| D5010224441 | Renault flywheel assembly | Two sellers; cast number not confirmed on our stock |
| D5010224440 | Renault flywheel, China 5 | Single source |
D5010330691 is the one to keep in your notes. It is the only number in this whole family where we have both a cast mark on our own stock and an independent 152 tooth figure from sellers.

152 teeth on a DCi11 flywheel is worth remembering because it does not match the European truck numbers we normally quote. MAN and Mercedes run 160 teeth, Scania 158, Volvo D12 153. A DCi11 at 152 sits just under the Volvo figure. Do not substitute one for the other on a tooth count alone.

What the Cast-In Marks Actually Prove
Four of the flywheels in this article carry the full part number in the casting itself, not a mould code:
- 1005120-E4200
- 1005120-E4600
- 1005120-E8100
- 1005120-E9500
- D5010330691

That is unusually clean. On most Chinese castings the raised characters are a mould number or a heat code, and reading a part number off them is a mistake. Here the pattern number and the part number are the same, which makes photo verification possible at the bench.

Two flywheels in this article do not have a confirmed cast number. E4201 and E9300 are photographed from the machined face, and the batch marks on those faces are not part numbers. We list them by the number the customer supplies, and we say so in the quotation rather than inventing a casting we cannot see.

Ordering Checklist
Before you place an order for any Dongfeng DDi or DCi11 flywheel, confirm four things. Each one has caused a wrong shipment at least once.
- Assembly or body. Is the requirement 1005115-Exxxx with the ring gear fitted, or 1005120-Exxxx as a bare disc.
- Engine designation. DDi47, DDi75, DDi11, DDi13 and DCi11 are five different flywheels with different balance and clutch interface.
- Tooth count. Count the starter ring if the old part is on the bench. Do not trust a catalogue figure alone, except where a seller publishes one and you can verify it.
- Clutch interface. Bolt circle, spigot bore and friction face height decide whether the clutch you have will sit correctly.

Send photos of both faces and one side profile, plus the cast number if there is one. That combination lets us cross-check the number against the drawing before quoting, instead of shipping a disc to someone who needed an assembly.

The Trap Hiding in the Same Prefix at FAW
The 1005115 and 1005120 prefixes also exist at FAW. Their meaning there is not the same as at Dongfeng, and this catches people who handle both brands.
| Prefix | At FAW (Jiefang, Dachai, Xichai) | At Dongfeng (DDi, DCi11) |
|---|---|---|
| 1005115 | Flywheel and ring gear assembly, Dachai 1005115 series | Flywheel and ring gear assembly, E family |
| 1005117 | Ring gear only, no flywheel | Not used in this family |
| 1005120 | Xichai flywheel assembly, a separate number range | Flywheel body, the level below 1005115 |
| 1005121 | Flywheel housing | Not used in this family |
At FAW, 1005115 and 1005120 belong to two different factories and you cannot look one up under the other. At Dongfeng, they belong to one part and describe two levels. Same digits, opposite logic.
We covered the FAW side in two earlier notes: the Dachai 1005115 range and the Xichai 1005120 range. Read those next if you also handle Jiefang trucks.

Making the Part, Not Just Sourcing It
Everything in this article was photographed on our own floor. The castings are poured in our foundry in Changyi, Shandong, machined on site, and the ring gears are pressed and checked for runout before packing.
That matters for two reasons. First, when a customer sends a drawing for a flywheel that no longer has a live part number, we can cut a pattern and quote it. Second, when someone questions whether a casting really carries the number they were promised, we can walk to the rack and photograph it. Most sellers of these parts cannot do either.

Frequently Asked Questions
Is 1005115-E9500 the same part as 1005120-E9500
They are two levels of one flywheel. 1005115-E9500 is quoted as the flywheel and ring gear assembly. 1005120-E9500 is quoted as the flywheel body. Confirm which level your invoice, or your customer’s order, actually requires.
Which Dongfeng engine uses a 1005120-E4600 flywheel
1005120-E4600 belongs to the Longqing DDi75 family fitted to the Tianlong KL. Trade listings describe 1005120-E4600 as the body number for 1005115-E4600, so the two sit on the same engine.
Why does my flywheel read D5010330691 instead of an E number
Because it is a DCi11 flywheel from the Renault era, not a DDi flywheel. Dongfeng kept the Renault number on those parts. D5010330691 is quoted by several sellers as a flywheel and ring gear assembly with 152 teeth.
Can I fit a 1005115 assembly where a 1005120 disc was used
Mechanically the flywheel body is the same part. Commercially the assembly includes the ring gear, so expect a higher price. Check that the ring gear you receive matches the tooth count of the starter already on the engine.
Does the number after the dash tell me the engine size
No. E4600 is a 7.5 litre class engine and E8100 is a 4.7 litre class engine. The four digits mark the platform generation, not the displacement.
Do you sell the ring gear separately from these flywheels
Yes. Ring gears for these families can be supplied separately, subject to tooth count and fit. Send the tooth count and the outer diameter and we will match it against our drawings.
What is the difference between D5010330691 and D5010224693
They are different flywheels. D5010330691 is quoted as a Renault flywheel and ring gear assembly with 152 teeth. D5010224693 is quoted for the China 5 DCi11 on the Tianlong KL. Do not treat them as interchangeable without checking the tooth count and clutch interface.
Can you produce a flywheel from a sample if the part number is obsolete
Yes. Send a sample or a drawing with the critical dimensions marked, and we will quote pattern, casting and machining as one package.
Get a Quote With the Number Verified First
Send us the part number, the engine designation and three photos: front face, rear face, side profile. We will confirm which level of the assembly you need before quoting, and tell you plainly if the number you have does not match the casting. Request a quote with your photos attached.
Irene, Changwei International. Email [email protected], WhatsApp and WeChat +86 199 5366 2121. Foundry in Wangke Industrial Zone, Changyi, Weifang, Shandong. FOB Qingdao.
Related Reading
- Dachai 1005115 flywheel part numbers: the FAW side of the same prefix
- Xichai 1005120 flywheel part numbers and three suffix formats
- Sinotruk MC07, MC11, MC13 and WD615 flywheel part numbers
- Gear rings: tooth count and interference fit basics