{"id":2001,"date":"2026-11-02T06:51:39","date_gmt":"2026-11-01T22:51:39","guid":{"rendered":"https:\/\/www.changweiintl.com\/en\/?post_type=ccm_blog&#038;p=2001"},"modified":"2026-11-03T10:24:13","modified_gmt":"2026-11-03T02:24:13","slug":"flywheel-bolt-torque-specs-torque-plus-angle-explained","status":"publish","type":"ccm_blog","link":"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained","title":{"rendered":"Flywheel Bolt Torque Specs: Torque Plus Angle Explained"},"content":{"rendered":"<div class=\"wrap\">\n<h2 id=\"table-of-contents\">Table of Contents<\/h2>\n<ul>\n<li><a href=\"#the-spec-has-two-halves\"><a href=\"#the-spec-has-two-halves\">The spec has two halves<\/a><\/a><\/li>\n<li><a href=\"#three-engines-three-procedures\"><a href=\"#three-engines-three-procedures\">Three engines, three procedures<\/a><\/a><\/li>\n<li><a href=\"#why-the-numbers-online-disagree-with-the-manual\"><a href=\"#why-the-numbers-online-disagree-with-the-manual\">Why the numbers online disagree with the manual<\/a><\/a><\/li>\n<li><a href=\"#where-the-torque-actually-goes\"><a href=\"#where-the-torque-actually-goes\">Where the torque actually goes<\/a><\/a><\/li>\n<li><a href=\"#the-dowel-pin-sets-timing-not-the-bolts\"><a href=\"#the-dowel-pin-sets-timing-not-the-bolts\">The dowel pin sets timing, not the bolts<\/a><\/a><\/li>\n<li><a href=\"#sequence-stages-and-guide-studs\"><a href=\"#sequence-stages-and-guide-studs\">Sequence, stages and guide studs<\/a><\/a><\/li>\n<li><a href=\"#lubricant-moves-clamp-load-more-than-your-wrench\"><a href=\"#lubricant-moves-clamp-load-more-than-your-wrench\">Lubricant moves clamp load more than your wrench<\/a><\/a><\/li>\n<li><a href=\"#what-to-measure-after-the-last-bolt\"><a href=\"#what-to-measure-after-the-last-bolt\">What to measure after the last bolt<\/a><\/a><\/li>\n<li><a href=\"#bolts-you-cannot-reuse\"><a href=\"#bolts-you-cannot-reuse\">Bolts you cannot reuse<\/a><\/a><\/li>\n<\/ul>\n<p>Search &#8220;flywheel bolt torque&#8221; for a Cummins ISX and you will find 95 to 110 N\u00b7m. The Cummins service manual for the same engine gives 125 N\u00b7m, then a second pass to 251 N\u00b7m. The chart is not a smaller version of the spec. It is half of it.<\/p>\n<p>That gap repeats across engine families. A flywheel joint is a friction joint, and friction is the least stable part of the assembly. Manufacturers either control friction with a fixed torque, or they control stretch with a fixed angle. Many do both. Read only the first number and the flywheel is not tight.<\/p>\n<h2 id=\"the-spec-has-two-halves\">The spec has two halves<\/h2>\n<p>A torque wrench measures resistance to turning. Only a small share of that resistance comes from the bolt being stretched against the flywheel. The rest is friction in the threads and under the bolt head, and friction changes with oil, plating, rust and burrs.<\/p>\n<p>A torque-plus-angle spec works differently. The wrench brings every bolt to the same starting load. A socket then turns each bolt a fixed number of degrees. Because thread pitch is constant, that turn equals a fixed amount of stretch, and stretch equals clamp load. Friction still varies, but it no longer decides the result.<\/p>\n<p>Isuzu states it plainly in the N-Series manual for the 4HK1-TC: tighten the flywheel bolts to 78 N\u00b7m, then turn them 120 to 150 degrees. There is no single torque value that reproduces that joint.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Six bolt holes and one smaller dowel hole on the crankshaft flange of an ISUZU 6BG1 flywheel\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/isuzu-6bg1-crank-flange-six-bolts.jpg\" \/><\/p>\n<p>The flange above is where the whole discussion happens: six bolt holes on a circle, plus one smaller dowel hole. Every torque value in this article acts on joints of exactly this shape.<\/p>\n<h2 id=\"three-engines-three-procedures\">Three engines, three procedures<\/h2>\n<p>The numbers below come from service manuals, not from parts catalogues. Where two editions or two language versions of the same manual were checked, the row says so.<\/p>\n<table>\n<thead>\n<tr>\n<th>Engine<\/th>\n<th>Bolts<\/th>\n<th>Stage 1<\/th>\n<th>Stage 2<\/th>\n<th>Notes<\/th>\n<th>Evidence<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Cummins ISX11.9 CM2250<\/td>\n<td>12<\/td>\n<td>125 N\u00b7m<\/td>\n<td>251 N\u00b7m<\/td>\n<td>Star pattern, oiled threads, guide studs<\/td>\n<td>OEM manual 016-005, EN and CN mirrors agree (dual source)<\/td>\n<\/tr>\n<tr>\n<td>Detroit MBE 4000<\/td>\n<td>10<\/td>\n<td>200 N\u00b7m<\/td>\n<td>plus 90 degrees<\/td>\n<td>Alternate sequence, two guide studs<\/td>\n<td>OEM manual 1.12, 2004 and EPA04 editions (dual source)<\/td>\n<\/tr>\n<tr>\n<td>Detroit Series 55<\/td>\n<td>not stated<\/td>\n<td>200-220 N\u00b7m<\/td>\n<td>plus 90-110 degrees<\/td>\n<td>Runout limit 0.08 mm at clutch face<\/td>\n<td>OEM manual 1.12 (single source)<\/td>\n<\/tr>\n<tr>\n<td>Isuzu 4HK1-TC<\/td>\n<td>not stated<\/td>\n<td>78 N\u00b7m<\/td>\n<td>plus 120-150 degrees<\/td>\n<td>Align to crank knock pin<\/td>\n<td>N-Series manual 6A-51, industrial 4HK1\/6HK1 manual agrees on housing values (dual source)<\/td>\n<\/tr>\n<tr>\n<td>Detroit 92 series<\/td>\n<td>not stated<\/td>\n<td>393-421 N\u00b7m<\/td>\n<td>none<\/td>\n<td>Much higher, older two-piece design<\/td>\n<td>Secondary compilation (single source, not used for advice)<\/td>\n<\/tr>\n<tr>\n<td>Detroit DD5<\/td>\n<td>not stated<\/td>\n<td>120 N\u00b7m<\/td>\n<td>plus 90 degrees<\/td>\n<td>Modern medium-duty<\/td>\n<td>Spec aggregator (single source)<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Two rows deserve a note. The 92 series figure is roughly double the MBE 4000 figure, even though both are Detroit Diesel engines. Family, bolt size and joint design change everything, so a number from another engine is not a starting point. The DD5 row is included only to show the pattern; it is not a substitute for that engine&#8217;s manual.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Friction face and ring gear of an ISUZU 6BG1 flywheel with six bolt holes through the hub\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/isuzu-6bg1-friction-face-ring-gear.jpg\" \/><\/p>\n<p>The same flywheel from the clutch side. Bolts clamp this face to the crankshaft; the ring gear on the rim is what the starter turns, and it is measured separately after installation.<\/p>\n<h2 id=\"why-the-numbers-online-disagree-with-the-manual\">Why the numbers online disagree with the manual<\/h2>\n<p>Three kinds of pages publish flywheel torque values. Each fails in a different way.<\/p>\n<table>\n<thead>\n<tr>\n<th>Page type<\/th>\n<th>Example claim<\/th>\n<th>What it leaves out<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Parts seller blog<\/td>\n<td>Cummins ISX &#8220;typical 95-110 N\u00b7m&#8221;<\/td>\n<td>Stops at the first stage; the manual continues to 251 N\u00b7m<\/td>\n<\/tr>\n<tr>\n<td>Generic spec site<\/td>\n<td>Isuzu NPR 4HK1 &#8220;about 76 N\u00b7m, two steps&#8221;<\/td>\n<td>Describes two torque steps; the manual&#8217;s second step is an angle<\/td>\n<\/tr>\n<tr>\n<td>Spec aggregator<\/td>\n<td>Isuzu 4JJ1 &#8220;110-130 N\u00b7m&#8221;<\/td>\n<td>Correct for that engine, wrong engine for the question<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>The first row is the most expensive. Someone tightening an ISX flywheel to 110 N\u00b7m has applied less than half of the specified 251 N\u00b7m. The bolt is not loose enough to fall out, which is why the error survives. It shows up later as a cracked flexplate, a worn pilot bore, or a clutch that will not release cleanly.<\/p>\n<p>The third row is a different trap. Numbers travel without their engine label. A 4JJ1 value looks plausible on a 4HK1 page because both are Isuzu four-cylinders.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Crankshaft bolt circle on an ISUZU 6HE1 flywheel with eight mounting holes\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/isuzu-6he1-crank-flange-eight-bolts.jpg\" \/><\/p>\n<p>Eight holes here, six on the 6BG1. Counting the bolt circle takes ten seconds and immediately tells you whether a quoted figure belongs to your part.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Crankshaft bolt circle on a HINO P11C flywheel with a dowel hole offset from the bolt circle\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/hino-p11c-crank-flange.jpg\" \/><\/p>\n<p>A HINO P11C flywheel from the same angle. The bolt circle sits on a machined hub, and a separate ring of holes further out carries the pressure plate.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Crankshaft bolt circle on a FUSO 6D17 flywheel\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/fuso-6d17-crank-flange.jpg\" \/><\/p>\n<p>A FUSO 6D17 flywheel. Different brand, same identification method: bolt circle first, then the dowel, then the ring gear teeth.<\/p>\n<h2 id=\"where-the-torque-actually-goes\">Where the torque actually goes<\/h2>\n<p>Fastener engineering uses a rough split that explains why torque-only specs scatter. Of the torque you apply, about half is consumed under the bolt head. About forty percent goes into the threads. About ten percent becomes clamp load.<\/p>\n<table>\n<thead>\n<tr>\n<th>Share of applied torque<\/th>\n<th>Where it goes<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>About 50 percent<\/td>\n<td>Friction under the bolt head or washer face<\/td>\n<\/tr>\n<tr>\n<td>About 40 percent<\/td>\n<td>Friction on the thread flanks<\/td>\n<\/tr>\n<tr>\n<td>About 10 percent<\/td>\n<td>Actual stretch of the bolt, which is the clamp load<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Four independent sources state the same ratio, which is why the industry calls it the 50-40-10 rule. The practical consequence is that a torque wrench is an indirect instrument. Torque control typically lands within about 25 percent of target preload; torque-plus-angle control lands within about 10 percent.<\/p>\n<p>The friction coefficient that drives this is usually written as K in the formula T = K x D x F. It is not a material constant. It depends on surface finish, coating and lubricant:<\/p>\n<table>\n<thead>\n<tr>\n<th>Thread condition<\/th>\n<th>Typical K value<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Dry, as-received carbon steel<\/td>\n<td>0.20 to 0.22<\/td>\n<\/tr>\n<tr>\n<td>Light rust-preventive oil<\/td>\n<td>0.18 to 0.20<\/td>\n<\/tr>\n<tr>\n<td>Engine oil on threads and under head<\/td>\n<td>0.14 to 0.16<\/td>\n<\/tr>\n<tr>\n<td>Molybdenum disulphide paste<\/td>\n<td>0.10 to 0.12<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Read that table as a warning. The same wrench setting on the same bolt can produce nearly double the clamp load if the thread condition changes. This is exactly why manuals specify the lubricant as carefully as the torque.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Crankshaft bolt circle on an ISUZU 6RB1 flywheel\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/isuzu-6rb1-crank-flange.jpg\" \/><\/p>\n<p>A larger flange from the same family. The bolt circle, the dowel and the spot faces are the three features that decide whether the joint holds.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Crankshaft bolt circle on an ISUZU 6WF1 flywheel\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/isuzu-6wf1-crank-flange.jpg\" \/><\/p>\n<p>The 6WF1 flange seen from the crankshaft side, with the bolt circle inside a machined hub. Flat, clean faces around each hole keep the friction under the head predictable, which is what a torque value assumes.<\/p>\n<h2 id=\"the-dowel-pin-sets-timing-not-the-bolts\">The dowel pin sets timing, not the bolts<\/h2>\n<p>Bolts clamp. They do not locate. On every engine in this article, a single dowel or knock pin fixes the flywheel&#8217;s angular position, and the bolts only hold it there.<\/p>\n<p>Cummins puts it as a caution in procedure 016-005. There is a timing dowel pin on the rear face of the crankshaft. If that pin is damaged, broken or missing, engine performance suffers and face runout goes out of specification. Isuzu&#8217;s instruction is shorter: install the flywheel along with the knock pin of the crankshaft. Detroit&#8217;s MBE 4000 procedure asks the technician to check the crankshaft dowel against the guide hole in the flywheel before any bolt is tightened.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Close-up of the dowel hole and six bolt holes on an ISUZU 6BG1 flywheel flange\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/isuzu-6bg1-dowel-hole-closeup.jpg\" \/><\/p>\n<p>The small hole at three o&#8217;clock is the dowel. It is deliberately a different diameter from the bolt holes, so a bolt cannot be started in it by mistake. If a used flywheel arrives with a bolt hole elongated or a dowel hole cracked, the part has been run loose.<\/p>\n<p>Two failure modes follow from this. A missing dowel lets the flywheel rotate slightly under clutch torque, which changes injection or ignition timing on engines that read the ring gear. A dowel that is present but damaged holds the flywheel off its seat, and the resulting face runout is often blamed on the flywheel itself.<\/p>\n<h2 id=\"sequence-stages-and-guide-studs\">Sequence, stages and guide studs<\/h2>\n<p>Both Cummins and Detroit specify a star pattern, and both split the job into stages. The reason is elastic interaction: tightening one bolt compresses the joint locally and relaxes its neighbours, so a single circular pass leaves the first bolts under-loaded.<\/p>\n<table>\n<thead>\n<tr>\n<th>Manual<\/th>\n<th>Order<\/th>\n<th>Staging<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Cummins ISX<\/td>\n<td>Star pattern, all 12 capscrews<\/td>\n<td>125 N\u00b7m, then 251 N\u00b7m<\/td>\n<\/tr>\n<tr>\n<td>Detroit MBE 4000<\/td>\n<td>Alternate sequence, all 10 bolts<\/td>\n<td>200 N\u00b7m, then 90 degrees<\/td>\n<\/tr>\n<tr>\n<td>Isuzu 4HK1-TC<\/td>\n<td>Order shown in the manual figure<\/td>\n<td>78 N\u00b7m, then 120-150 degrees<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Guide studs are part of the procedure, not a convenience. Cummins calls for two M6 x 1.5 guide studs so the flywheel is supported while the first bolts go in. Detroit installs eight bolts, then removes the two guide studs and fits the remaining two in their place. A flywheel that hangs on two bolts while the rest are started can shift and burr the dowel.<\/p>\n<p>The housing follows the same logic. The Cummins manual notes that the flywheel housing is located by two ring dowels on the block. Alignment must be rechecked if the housing is removed. Isuzu aligns the 4HK1 housing to the cylinder block knock pin and seals the joint with liquid gasket. The same manual gives the housing bolt torques as a staged set of 96, 77 and 38 N\u00b7m by bolt group.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Inner face of a Sinotruk-pattern flywheel housing with radial ribs and starter pocket\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/sinotruk-flywheel-housing-inner-ribs.jpg\" \/><\/p>\n<p>Inside a flywheel housing: radial ribs, a ring of bolt bosses around the crankshaft bore, and the starter pocket at the lower edge. Housing alignment is measured from the crankshaft bore, not from the outer flange.<\/p>\n<h2 id=\"lubricant-moves-clamp-load-more-than-your-wrench\">Lubricant moves clamp load more than your wrench<\/h2>\n<p>Cummins is unusually specific. Lubricate the threads and the underside of the capscrew heads with clean 15W-40 engine oil. Let the excess drip off. Do not lubricate the threads of the crankshaft. Detroit asks for a light coating of engine oil on the ten multipoint socket-head bolts.<\/p>\n<p>The instruction to leave the crankshaft threads dry is not a detail. A blind hole packed with oil hydraulically resists the bolt, and the wrench clicks before the joint is actually tight.<\/p>\n<table>\n<thead>\n<tr>\n<th>What the manual says<\/th>\n<th>Why it matters<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Oil the bolt threads and under the head<\/td>\n<td>Sets K near 0.15 instead of 0.20<\/td>\n<\/tr>\n<tr>\n<td>Do not oil the crankshaft threads<\/td>\n<td>Prevents hydraulic lock in a blind hole<\/td>\n<\/tr>\n<tr>\n<td>Use identical replacement capscrews<\/td>\n<td>Different grades and thread forms change friction<\/td>\n<\/tr>\n<tr>\n<td>Minimum SAE Grade 8 with rolled threads (Cummins)<\/td>\n<td>Cut threads and lower grades stretch differently<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2 id=\"what-to-measure-after-the-last-bolt\">What to measure after the last bolt<\/h2>\n<p>Torque is an input. Runout is the result, and it is the number that decides whether the clutch will live.<\/p>\n<table>\n<thead>\n<tr>\n<th>Measurement<\/th>\n<th>Limit<\/th>\n<th>Source<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Flywheel bore runout, Cummins ISX<\/td>\n<td>0.127 mm maximum<\/td>\n<td>Cummins manual 016-005<\/td>\n<\/tr>\n<tr>\n<td>Flywheel runout at clutch contact face, Series 55<\/td>\n<td>0.08 mm maximum<\/td>\n<td>Detroit manual 1.12<\/td>\n<\/tr>\n<tr>\n<td>Ring gear radial runout after fitting<\/td>\n<td>0.5 mm or less<\/td>\n<td>MBE 900 and MBE 4000 manuals<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Measure with the dial indicator mounted on the flywheel housing, not on the engine block. The housing is the reference the starter and clutch actually see. Rotate the crankshaft one full turn and read the total indicator movement. If bore runout is out of limit, Cummins says to remove the flywheel and inspect the mounting faces. Refit it and measure again before condemning the part.<\/p>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Machined face of a flywheel housing with bolt bosses visible\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/sinotruk-flywheel-housing-machined-face.jpg\" \/><\/p>\n<p>The machined face in the foreground is the surface the dial indicator base sits on. A dirty or burred face gives a false runout reading before the flywheel is even blamed.<\/p>\n<p>More on measurement method and limits is in our guide to <a href=\"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-and-ring-gear-runout-tir-how-to-measure-it-and-what-the-limits-actually-are\">flywheel and ring gear runout<\/a>.<\/p>\n<h2 id=\"bolts-you-cannot-reuse\">Bolts you cannot reuse<\/h2>\n<p>Any specification that ends in degrees is a torque-to-yield joint. The bolt is turned past its elastic limit on purpose, so the clamp load stays stable instead of drifting with friction.<\/p>\n<p>That has one consequence for the workshop. The bolt has already been stretched once. The angle that produced the correct clamp load on a new bolt will not produce it on a used one. Industry sources put the loss of clamp load on a reused torque-to-yield bolt at 15 to 30 percent. Treat that figure as a general industry estimate rather than a measured value for any specific engine.<\/p>\n<p>Detroit gives a direct way to check. The MBE 4000 procedure lists a maximum shaft length of 77.0 mm for the flywheel bolts. A bolt that measures longer has already stretched and does not belong in the engine.<\/p>\n<table>\n<thead>\n<tr>\n<th>Situation<\/th>\n<th>Action<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Manual specifies torque plus angle<\/td>\n<td>Fit new bolts; measure old ones against the length limit if given<\/td>\n<\/tr>\n<tr>\n<td>Manual specifies torque only, standard hex bolt<\/td>\n<td>Reuse only if threads and shank are undamaged and the manual allows it<\/td>\n<\/tr>\n<tr>\n<td>Bolt shows necking, thread galling or a bright wear ring<\/td>\n<td>Replace regardless of the manual<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><img decoding=\"async\" loading=\"lazy\" alt=\"Side view of a flywheel housing showing the machined sensor boss\" src=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/sinotruk-flywheel-housing-sensor-boss.jpg\" \/><\/p>\n<p>A machined boss and bore on the side of the housing. On electronically controlled engines this is where the crank position sensor reads the flywheel, which is another reason housing alignment is not optional.<\/p>\n<h2 id=\"frequently-asked-questions\">Frequently Asked Questions<\/h2>\n<h3 id=\"can-i-tighten-flywheel-bolts-in-one-pass-to-the-final-value\">Can I tighten flywheel bolts in one pass to the final value?<\/h3>\n<p>No. Every manual checked here uses two stages or a stage plus an angle. A single pass leaves the first bolts under-loaded because each later bolt relaxes its neighbours.<\/p>\n<h3 id=\"my-manual-gives-only-one-torque-figure-is-something-missing\">My manual gives only one torque figure. Is something missing?<\/h3>\n<p>Not necessarily. Some joints are pure torque joints. The problem runs the other way: third-party charts often copy only the first stage of a two-stage spec. Compare your figure against the OEM manual for your exact engine code before use.<\/p>\n<h3 id=\"does-thread-locker-replace-the-angle-step\">Does thread locker replace the angle step?<\/h3>\n<p>No. Thread locker changes friction and helps against vibration. It does not stretch the bolt to the designed clamp load, and adding it to an angle-spec joint changes the friction the spec was written around.<\/p>\n<h3 id=\"why-does-my-flywheel-have-six-bolt-holes-when-the-manual-describes-twelve\">Why does my flywheel have six bolt holes when the manual describes twelve?<\/h3>\n<p>Bolt count is a property of the crankshaft flange, not of the engine family name. The Cummins ISX uses twelve capscrews; the Detroit MBE 4000 uses ten. Count the holes on the part in front of you.<\/p>\n<h3 id=\"can-i-reuse-flywheel-bolts\">Can I reuse flywheel bolts?<\/h3>\n<p>Only if the manual allows it and the bolts pass inspection. If the procedure ends with a degree figure, the bolts are torque-to-yield and are intended for one installation.<\/p>\n<h3 id=\"how-do-i-order-the-right-flywheel-if-the-part-number-plate-is-gone\">How do I order the right flywheel if the part number plate is gone?<\/h3>\n<p>Send four things: a photo of the crankshaft flange, the number of bolt holes, the number of ring gear teeth, and the engine code from the block. Our <a href=\"https:\/\/www.changweiintl.com\/en\/blog\/isuzu-flywheel-part-numbers-6bg1-6he1-6hk1-6sd1-6wf1-6wg1-size-and-teeth-chart\">ISUZU part number chart<\/a> and <a href=\"https:\/\/www.changweiintl.com\/en\/blog\/mercedes-906-030-flywheel-part-numbers-133-vs-146-teeth\">Mercedes 906 030 chart<\/a> show how that information maps to real numbers.<\/p>\n<h2 id=\"sending-us-the-right-information\">Sending Us the Right Information<\/h2>\n<p>We cast and machine flywheels, ring gears and flywheel housings to drawings and to OEM numbers. We quote from the information a workshop actually has: photos, tooth counts and engine codes.<\/p>\n<p>If you are replacing a flywheel and the manual is missing, send us the flange photo and the engine code. We will confirm the bolt circle, the dowel position and the ring gear before anything is quoted.<\/p>\n<p>Browse <a href=\"https:\/\/www.changweiintl.com\/en\/product\">our product range<\/a> or the <a href=\"https:\/\/www.changweiintl.com\/en\/product\/gear-ring\">ring gear range<\/a>, and send your list through the <a href=\"https:\/\/www.changweiintl.com\/en\/quote\">quote form<\/a>. FOB Qingdao, IATF 16949 foundry.<\/p>\n<h3 id=\"related-reading\">Related reading<\/h3>\n<ul>\n<li><a href=\"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-and-ring-gear-runout-tir-how-to-measure-it-and-what-the-limits-actually-are\">Flywheel and ring gear runout: how to measure it<\/a><\/li>\n<li><a href=\"https:\/\/www.changweiintl.com\/en\/blog\/isuzu-flywheel-part-numbers-6bg1-6he1-6hk1-6sd1-6wf1-6wg1-size-and-teeth-chart\">ISUZU flywheel part numbers by engine<\/a><\/li>\n<li><a href=\"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-timing-marks-tdc-line-degree-scale-date-code\">Flywheel timing marks: TDC line, degree scale, date code<\/a><\/li>\n<\/ul>\n<h3 id=\"a-note-on-the-data-in-this-article\">A note on the data in this article<\/h3>\n<p>Torque, angle, runout and lubricant values are taken from OEM service manuals named in the tables. The 92 series and DD5 rows, and the 15 to 30 percent reuse figure, come from single secondary sources and are marked as such. We do not publish a torque value we cannot attribute to a document. Where a manual does not state a bolt count or a stage value, the table says so instead of filling the gap.<\/p>\n<\/div>\n<p><!-- cw-schema:begin --><br \/>\n<script type=\"application\/ld+json\">{\"@context\":\"https:\/\/schema.org\",\"@type\":\"BlogPosting\",\"headline\":\"Flywheel Bolt Torque Specs: Torque Plus Angle Explained\",\"datePublished\":\"2026-11-02T06:51:39\",\"dateModified\":\"2026-11-02T06:51:39\",\"author\":{\"@type\":\"Organization\",\"name\":\"Changwei Intelligent Equipment\",\"url\":\"https:\/\/www.changweiintl.com\"},\"publisher\":{\"@type\":\"Organization\",\"name\":\"Changwei Intelligent Equipment\",\"url\":\"https:\/\/www.changweiintl.com\",\"logo\":{\"@type\":\"ImageObject\",\"url\":\"https:\/\/www.changweiintl.com\/logo.png\"}},\"mainEntityOfPage\":{\"@type\":\"WebPage\",\"@id\":\"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained\"},\"inLanguage\":\"en\"}<\/script><br \/>\n<script type=\"application\/ld+json\">{\"@context\":\"https:\/\/schema.org\",\"@type\":\"FAQPage\",\"mainEntity\":[{\"@type\":\"Question\",\"name\":\"Can I tighten flywheel bolts in one pass to the final value?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"No. Every manual checked here uses two stages or a stage plus an angle. A single pass leaves the first bolts under-loaded because each later bolt relaxes its neighbours.\"}},{\"@type\":\"Question\",\"name\":\"My manual gives only one torque figure. Is something missing?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Not necessarily. Some joints are pure torque joints. The problem runs the other way: third-party charts often copy only the first stage of a two-stage spec. Compare your figure against the OEM manual for your exact engine code before use.\"}},{\"@type\":\"Question\",\"name\":\"Does thread locker replace the angle step?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"No. Thread locker changes friction and helps against vibration. It does not stretch the bolt to the designed clamp load, and adding it to an angle-spec joint changes the friction the spec was written around.\"}},{\"@type\":\"Question\",\"name\":\"Why does my flywheel have six bolt holes when the manual describes twelve?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Bolt count is a property of the crankshaft flange, not of the engine family name. The Cummins ISX uses twelve capscrews; the Detroit MBE 4000 uses ten. Count the holes on the part in front of you.\"}},{\"@type\":\"Question\",\"name\":\"Can I reuse flywheel bolts?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Only if the manual allows it and the bolts pass inspection. If the procedure ends with a degree figure, the bolts are torque-to-yield and are intended for one installation.\"}},{\"@type\":\"Question\",\"name\":\"How do I order the right flywheel if the part number plate is gone?\",\"acceptedAnswer\":{\"@type\":\"Answer\",\"text\":\"Send four things: a photo of the crankshaft flange, the number of bolt holes, the number of ring gear teeth, and the engine code from the block. Our ISUZU part number chart and Mercedes 906 030 chart show how that information maps to real numbers.\"}}]}<\/script><br \/>\n<!-- cw-schema:end --><\/p>\n","protected":false},"excerpt":{"rendered":"<p>A flywheel bolt spec is two instructions, not one: a torque value and often an angle. Here are the real numbers from Cummins, Detroit and Isuzu service manuals, why generic torque charts understate them, and what to measure after the last bolt.<\/p>","protected":false},"author":1,"featured_media":1990,"template":"","meta":{"_yoast_wpseo_focuskw":"flywheel bolt torque specs","_yoast_wpseo_title":"","_yoast_wpseo_metadesc":"","_cw_seo_title_en":"Flywheel Bolt Torque Specs: Torque Plus Angle Explained","_cw_seo_metadesc_en":"Cummins ISX: 125 then 251 N.m. Detroit MBE 4000: 200 N.m plus 90 degrees. Isuzu 4HK1: 78 N.m plus 120-150 degrees. Why one number is never the whole spec."},"ccm_blog_tag":[199,200,198,201,202],"class_list":["post-2001","ccm_blog","type-ccm_blog","status-publish","has-post-thumbnail","hentry"],"yoast_head":"<!-- This site is optimized with the Yoast SEO plugin v28.9 - https:\/\/yoast.com\/product\/yoast-seo-wordpress\/ -->\n<title>Flywheel Bolt Torque Specs: Torque Plus Angle Explained &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.<\/title>\n<meta name=\"robots\" content=\"index, follow, max-snippet:-1, max-image-preview:large, max-video-preview:-1\" \/>\n<link rel=\"canonical\" href=\"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained\/\" \/>\n<meta property=\"og:locale\" content=\"en_US\" \/>\n<meta property=\"og:type\" content=\"article\" \/>\n<meta property=\"og:title\" content=\"Flywheel Bolt Torque Specs: Torque Plus Angle Explained &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.\" \/>\n<meta property=\"og:description\" content=\"A flywheel bolt spec is two instructions, not one: a torque value and often an angle. Here are the real numbers from Cummins, Detroit and Isuzu service manuals, why generic torque charts understate them, and what to measure after the last bolt.\" \/>\n<meta property=\"og:url\" content=\"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained\/\" \/>\n<meta property=\"og:site_name\" content=\"Weifang Changwei Intelligent Equipment Co., Ltd.\" \/>\n<meta property=\"article:publisher\" content=\"https:\/\/www.facebook.com\/profile.php?id=61573276931730\" \/>\n<meta property=\"article:modified_time\" content=\"2026-11-03T02:24:13+00:00\" \/>\n<meta property=\"og:image\" content=\"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/fuso-6d17-crank-flange.jpg\" \/>\n\t<meta property=\"og:image:width\" content=\"1200\" \/>\n\t<meta property=\"og:image:height\" content=\"900\" \/>\n\t<meta property=\"og:image:type\" content=\"image\/jpeg\" \/>\n<meta name=\"twitter:card\" content=\"summary_large_image\" \/>\n<meta name=\"twitter:label1\" content=\"Est. reading time\" \/>\n\t<meta name=\"twitter:data1\" content=\"17 minutes\" \/>\n<script type=\"application\/ld+json\" class=\"yoast-schema-graph\">{\"@context\":\"https:\\\/\\\/schema.org\",\"@graph\":[{\"@type\":\"WebPage\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/flywheel-bolt-torque-specs-torque-plus-angle-explained\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/flywheel-bolt-torque-specs-torque-plus-angle-explained\",\"name\":\"Flywheel Bolt Torque Specs: Torque Plus Angle Explained &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.\",\"isPartOf\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#website\"},\"primaryImageOfPage\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/flywheel-bolt-torque-specs-torque-plus-angle-explained#primaryimage\"},\"image\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/flywheel-bolt-torque-specs-torque-plus-angle-explained#primaryimage\"},\"thumbnailUrl\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/fuso-6d17-crank-flange.jpg\",\"datePublished\":\"2026-11-01T22:51:39+00:00\",\"dateModified\":\"2026-11-03T02:24:13+00:00\",\"breadcrumb\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/flywheel-bolt-torque-specs-torque-plus-angle-explained#breadcrumb\"},\"inLanguage\":\"en-US\",\"potentialAction\":[{\"@type\":\"ReadAction\",\"target\":[\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/flywheel-bolt-torque-specs-torque-plus-angle-explained\"]}]},{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/flywheel-bolt-torque-specs-torque-plus-angle-explained#primaryimage\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/fuso-6d17-crank-flange.jpg\",\"contentUrl\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/11\\\/fuso-6d17-crank-flange.jpg\",\"width\":1200,\"height\":900,\"caption\":\"Crankshaft bolt circle on a FUSO 6D17 flywheel\"},{\"@type\":\"BreadcrumbList\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\\\/flywheel-bolt-torque-specs-torque-plus-angle-explained#breadcrumb\",\"itemListElement\":[{\"@type\":\"ListItem\",\"position\":1,\"name\":\"Home\",\"item\":\"https:\\\/\\\/www.changweiintl.com\\\/en\\\/\"},{\"@type\":\"ListItem\",\"position\":2,\"name\":\"Blog\",\"item\":\"https:\\\/\\\/www.changweiintl.com\\\/blog\"},{\"@type\":\"ListItem\",\"position\":3,\"name\":\"Flywheel Bolt Torque Specs: Torque Plus Angle Explained\"}]},{\"@type\":\"WebSite\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#website\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/\",\"name\":\"Weifang Changwei Inteligent Equipment Co, Ltd\",\"description\":\"Changwei is a China manufacturer of engine flywheels, ring gears, flywheel housings and gear chambers. IATF 16949 certified OEM\\\/ODM supplier.\",\"publisher\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#organization\"},\"potentialAction\":[{\"@type\":\"SearchAction\",\"target\":{\"@type\":\"EntryPoint\",\"urlTemplate\":\"https:\\\/\\\/www.changweiintl.com\\\/?s={search_term_string}\"},\"query-input\":{\"@type\":\"PropertyValueSpecification\",\"valueRequired\":true,\"valueName\":\"search_term_string\"}}],\"inLanguage\":\"en-US\"},{\"@type\":\"Organization\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#organization\",\"name\":\"Weifang Changwei Intelligent Equipment Co., Ltd.\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/\",\"logo\":{\"@type\":\"ImageObject\",\"inLanguage\":\"en-US\",\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#\\\/schema\\\/logo\\\/image\\\/\",\"url\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/06\\\/1782266646-favicon-512.png\",\"contentUrl\":\"https:\\\/\\\/www.changweiintl.com\\\/wp-content\\\/uploads\\\/2026\\\/06\\\/1782266646-favicon-512.png\",\"width\":512,\"height\":512,\"caption\":\"Weifang Changwei Inteligent Equipment Co, Ltd\"},\"image\":{\"@id\":\"https:\\\/\\\/www.changweiintl.com\\\/#\\\/schema\\\/logo\\\/image\\\/\"},\"sameAs\":[\"https:\\\/\\\/www.facebook.com\\\/profile.php?id=61573276931730\"],\"legalName\":\"Weifang Changwei Intelligent Equipment Co., Ltd.\",\"alternateName\":[\"Changwei\",\"\u6f4d\u574a\u660c\u7ef4\u667a\u80fd\u8bbe\u5907\u6709\u9650\u516c\u53f8\"],\"address\":{\"@type\":\"PostalAddress\",\"streetAddress\":\"Zhicheng World Trade Center, High-Tech Zone\",\"addressLocality\":\"Weifang\",\"addressRegion\":\"Shandong\",\"addressCountry\":\"CN\"},\"contactPoint\":[{\"@type\":\"ContactPoint\",\"contactType\":\"sales\",\"availableLanguage\":[\"en\",\"zh\"],\"email\":\"tony15589697779@gmail.com\",\"telephone\":\"+8615589697779\"}],\"knowsAbout\":[\"engine flywheel\",\"flywheel ring gear\",\"flywheel housing\",\"gear chamber\",\"OEM engine components\",\"IATF 16949 certified manufacturing\"],\"areaServed\":\"Worldwide\"}]}<\/script>\n<!-- \/ Yoast SEO plugin. -->","yoast_head_json":{"title":"Flywheel Bolt Torque Specs: Torque Plus Angle Explained &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.","robots":{"index":"index","follow":"follow","max-snippet":"max-snippet:-1","max-image-preview":"max-image-preview:large","max-video-preview":"max-video-preview:-1"},"canonical":"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained\/","og_locale":"en_US","og_type":"article","og_title":"Flywheel Bolt Torque Specs: Torque Plus Angle Explained &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.","og_description":"A flywheel bolt spec is two instructions, not one: a torque value and often an angle. Here are the real numbers from Cummins, Detroit and Isuzu service manuals, why generic torque charts understate them, and what to measure after the last bolt.","og_url":"https:\/\/www.changweiintl.com\/en\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained\/","og_site_name":"Weifang Changwei Intelligent Equipment Co., Ltd.","article_publisher":"https:\/\/www.facebook.com\/profile.php?id=61573276931730","article_modified_time":"2026-11-03T02:24:13+00:00","og_image":[{"width":1200,"height":900,"url":"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/fuso-6d17-crank-flange.jpg","type":"image\/jpeg"}],"twitter_card":"summary_large_image","twitter_misc":{"Est. reading time":"17 minutes"},"schema":{"@context":"https:\/\/schema.org","@graph":[{"@type":"WebPage","@id":"https:\/\/www.changweiintl.com\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained","url":"https:\/\/www.changweiintl.com\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained","name":"Flywheel Bolt Torque Specs: Torque Plus Angle Explained &#8211; Weifang Changwei Intelligent Equipment Co., Ltd.","isPartOf":{"@id":"https:\/\/www.changweiintl.com\/#website"},"primaryImageOfPage":{"@id":"https:\/\/www.changweiintl.com\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained#primaryimage"},"image":{"@id":"https:\/\/www.changweiintl.com\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained#primaryimage"},"thumbnailUrl":"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/fuso-6d17-crank-flange.jpg","datePublished":"2026-11-01T22:51:39+00:00","dateModified":"2026-11-03T02:24:13+00:00","breadcrumb":{"@id":"https:\/\/www.changweiintl.com\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained#breadcrumb"},"inLanguage":"en-US","potentialAction":[{"@type":"ReadAction","target":["https:\/\/www.changweiintl.com\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained"]}]},{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.changweiintl.com\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained#primaryimage","url":"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/fuso-6d17-crank-flange.jpg","contentUrl":"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/11\/fuso-6d17-crank-flange.jpg","width":1200,"height":900,"caption":"Crankshaft bolt circle on a FUSO 6D17 flywheel"},{"@type":"BreadcrumbList","@id":"https:\/\/www.changweiintl.com\/blog\/flywheel-bolt-torque-specs-torque-plus-angle-explained#breadcrumb","itemListElement":[{"@type":"ListItem","position":1,"name":"Home","item":"https:\/\/www.changweiintl.com\/en\/"},{"@type":"ListItem","position":2,"name":"Blog","item":"https:\/\/www.changweiintl.com\/blog"},{"@type":"ListItem","position":3,"name":"Flywheel Bolt Torque Specs: Torque Plus Angle Explained"}]},{"@type":"WebSite","@id":"https:\/\/www.changweiintl.com\/#website","url":"https:\/\/www.changweiintl.com\/","name":"Weifang Changwei Inteligent Equipment Co, Ltd","description":"Changwei is a China manufacturer of engine flywheels, ring gears, flywheel housings and gear chambers. IATF 16949 certified OEM\/ODM supplier.","publisher":{"@id":"https:\/\/www.changweiintl.com\/#organization"},"potentialAction":[{"@type":"SearchAction","target":{"@type":"EntryPoint","urlTemplate":"https:\/\/www.changweiintl.com\/?s={search_term_string}"},"query-input":{"@type":"PropertyValueSpecification","valueRequired":true,"valueName":"search_term_string"}}],"inLanguage":"en-US"},{"@type":"Organization","@id":"https:\/\/www.changweiintl.com\/#organization","name":"Weifang Changwei Intelligent Equipment Co., Ltd.","url":"https:\/\/www.changweiintl.com\/","logo":{"@type":"ImageObject","inLanguage":"en-US","@id":"https:\/\/www.changweiintl.com\/#\/schema\/logo\/image\/","url":"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/06\/1782266646-favicon-512.png","contentUrl":"https:\/\/www.changweiintl.com\/wp-content\/uploads\/2026\/06\/1782266646-favicon-512.png","width":512,"height":512,"caption":"Weifang Changwei Inteligent Equipment Co, Ltd"},"image":{"@id":"https:\/\/www.changweiintl.com\/#\/schema\/logo\/image\/"},"sameAs":["https:\/\/www.facebook.com\/profile.php?id=61573276931730"],"legalName":"Weifang Changwei Intelligent Equipment Co., Ltd.","alternateName":["Changwei","\u6f4d\u574a\u660c\u7ef4\u667a\u80fd\u8bbe\u5907\u6709\u9650\u516c\u53f8"],"address":{"@type":"PostalAddress","streetAddress":"Zhicheng World Trade Center, High-Tech Zone","addressLocality":"Weifang","addressRegion":"Shandong","addressCountry":"CN"},"contactPoint":[{"@type":"ContactPoint","contactType":"sales","availableLanguage":["en","zh"],"email":"tony15589697779@gmail.com","telephone":"+8615589697779"}],"knowsAbout":["engine flywheel","flywheel ring gear","flywheel housing","gear chamber","OEM engine components","IATF 16949 certified manufacturing"],"areaServed":"Worldwide"}]}},"_links":{"self":[{"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/ccm_blog\/2001","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/ccm_blog"}],"about":[{"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/types\/ccm_blog"}],"author":[{"embeddable":true,"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/users\/1"}],"version-history":[{"count":3,"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/ccm_blog\/2001\/revisions"}],"predecessor-version":[{"id":2004,"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/ccm_blog\/2001\/revisions\/2004"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/media\/1990"}],"wp:attachment":[{"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/media?parent=2001"}],"wp:term":[{"taxonomy":"ccm_blog_tag","embeddable":true,"href":"https:\/\/www.changweiintl.com\/en\/wp-json\/wp\/v2\/ccm_blog_tag?post=2001"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}