Get a quote now
Blog 2026-10-21

Weichai Flywheel Housing Part Numbers: 6126000 Chart

Weichai Flywheel Housing Part Numbers: 6126000 Series and PTO Openings

A flywheel housing is the largest casting bolted to the back of a diesel engine, and it is the part most often ordered wrong. Not because buyers are careless, but because the number on the old housing often does not describe the housing you need: the same casting is listed under several numbers, one number is listed under several engines, and the power take-off opening can move from one side to the other without the number changing at all.

This page covers the Weichai 6126000 family as we actually see it in the foundry, the Cummins numbers that turn up in the same orders, and the three checks that decide whether a housing will bolt up.

Table of Contents

Why the Number Alone Does Not Identify a Housing

Three things vary independently on these castings, and a part number does not always pin down all three.

The first is the SAE flange size at the gearbox end. The second is where the power take-off aperture sits, which can be left, centre or right. The third is the sensor bore on the side, present on some castings and blank on others. Get any one of them wrong and the housing either will not bolt to the transmission, or it will bolt on and put the input shaft out of alignment.

Weichai flywheel housing, painted and finished, on the shop floor

A housing that fits but runs out of alignment is worse than one that does not fit. The driver notices nothing for a few thousand kilometres, and then the input shaft bearing and the clutch release bearing are scrap.

The 6126000 Family and the Digit That Sorts It

Weichai’s older twelve-digit system is not random. The digits after the 6126000 prefix group parts by function, and that grouping is stable across the family.

Parts starting 6126000 1 belong to the housing and front-end group: flywheel housings, timing gear housings, covers. Parts starting 6126000 2 belong to the flywheel and driveline group: flywheels, ring gears, flywheel bolts.

Prefix Group Examples
6126000 1 xxxx Housings and front end 612600010012 flywheel housing, 612600011783 timing gear housing
6126000 2 xxxx Flywheel and driveline 612600020208 ring gear, 612600020211 flywheel

This is useful in both directions. If a customer sends a number beginning 61260001, it is a housing of some kind and not a flywheel, which narrows the search immediately. If you are holding a housing and the cast number starts 61260002, you are not holding a flywheel housing.

The same logic runs through the timing gear housing range, which we set out in the 6126000 timing gear housing part number guide.

Bare flywheel housing casting before painting

Newer Weichai parts moved to a ten-digit system with no functional grouping at all, and some series use their own blocks entirely, with 615 for the WD615 generation and 6126 for later platforms. That is why a single engine family can appear under three different number formats in the same year.

Weichai Flywheel Housing Part Numbers

The table below lists what we can support. The evidence column matters more than the number: a figure that appears on one supplier page and nowhere else is a lead, not a fact.

Part number Listed for Description Evidence
612600010305 WP10 and WD615 Flywheel housing Three sources, engine attribution conflicts
612600013608 WP12, WD615, Euro II Flywheel housing Two sources, consistent
612600011619 WP10, concrete mixer, right-hand PTO Flywheel housing, 0.179 m3, listed at 80 kg packed One source, most detailed description
612600011088 WP10 Flywheel housing One source only
612600013594 WP10, bus application Flywheel housing One source only
612600011873 Not stated Flywheel housing One source only
612600010012 Not stated Flywheel housing One source, two conflicting weights
61500010012 WD615, Euro II Flywheel housing One source only
1000295905 WP12 and WP13 Flywheel housing assembly One source only
1001103608 Ruili series Flywheel housing Three sources, consistent
612630030001 Not stated Flywheel housing connecting plate One source only
612630030006R P12 Flywheel housing One source only
13026867 WP6, 226B Flywheel housing One source only

Two entries in that table deserve a closer look.

612600010305 is offered by three separate suppliers. Two of them label it WP10 and one labels it WD615. All three may be right if the same casting serves both engine generations, but the buyer cannot tell from the listing, and the safe assumption is that the number alone will not settle it.

612600011619 carries the most useful description of any number in the list: WP10, concrete mixer, right-hand power take-off, except Beiben and Hualing applications. That is a part number doing what a part number should do, and it is rare.

Sixteen-bolt machined face on a Weichai flywheel housing

The PTO Opening Decides Fitment

This is the part of the page worth reading twice.

We hold castings that are identical in flange size, identical in depth and identical in bore, and differ only in which side the power take-off aperture is cast into. The photograph below shows three of them side by side.

Three Weichai flywheel housings with PTO openings on the left, centre and right

Left, centre, right. On a concrete mixer the PTO drives the drum through a shaft that has to line up with the pump, so the aperture position is a functional requirement, not a preference. Fit a centre-PTO housing where a right-PTO one was specified and the truck does not work.

In the number lists this distinction often disappears. A number is quoted as fitting WP10, and the PTO position is buried in one supplier’s description or omitted entirely. If you are ordering for a mixer, a crane or a refuse body, state the PTO side in the enquiry. Do not assume the number implies it.

Machined sensor bore on the side of a flywheel housing

The same applies to the sensor bore. Some castings have a machined pad with a bore for the crankshaft position sensor, and some have the pad but no bore. The photograph above is a machined bore; the one below is the same feature on a centre-PTO casting.

Sensor bore on a centre-PTO flywheel housing

There are also timing marks cast or stamped near the starter aperture on some housings, used when setting injection timing. They are easy to miss and impossible to add afterwards.

Timing marks near the starter aperture on a flywheel housing

A Cast Number You Can Actually Read

Most cast markings on these housings are mould numbers, date codes and batch codes. Occasionally a real part number is cast into the part, and when it is, it is worth photographing.

Centre-PTO Weichai flywheel housing with 612600010018 cast into the side

The centre-PTO housing above carries 612600010018 cast into the flank, with a date code of 2011.9 and a batch code below it. The number is clear, it is on the part, and it is not a mould number.

We have not found an independent catalogue entry for 612600010018, so we do not quote it as an official number on its own. What we do is treat it as a strong hint: a customer holding that casting is holding a centre-PTO housing from the 6126000 family, and we confirm the rest from the flange and the bore before we quote.

Finished flywheel housings stacked for packing

The back face is where the engine side is machined, and it is the face that tells you the most about which engine the housing came from.

Rear face of a Weichai flywheel housing

Cummins Numbers That Share the Same Warehouse

Orders for Weichai housings frequently arrive alongside Cummins numbers, and the Cummins side has its own trap: several numbers fit the same engine list.

Part number Listed for Note
4947472 / C4947472 6L, 6CT, L375, 6LTAA Three sources agree
5253948 ISL9, QSL9, QSC8.3 and 28 further models Same 32-model list as 5253952
5253952 ISL9, QSL9, QSC8.3 and 28 further models Same list, reference price around CNY 6,794
3960668 / C3960668 6CT, 6L Aftermarket listings name 5253952 and 4947472 as replacements

Cummins 4947472 flywheel housing, front face

5253948 and 5253952 are both real, both listed against the same 32 engine models, and both sold as the housing for an ISL9 or QSL9. One supplier quotes a reference price for 5253952 and leaves 5253948 on request. We do not treat them as interchangeable without checking the flange and the PTO opening on the actual part, because two numbers with the same engine list can still differ in the casting.

Cummins 5253948 flywheel housing, front face

Cummins 5253948 flywheel housing, side view

Weight Figures on These Housings Do Not Agree

Freight is priced by volume and by weight, so the weight matters. Published figures for these castings are unreliable.

One page for 612600010012 gives 10.35 kg in the description and 5.3 kg in the specification table on the same page. A flywheel housing for a heavy truck engine does not weigh five kilograms, and the honest reading is that neither figure has been checked.

612600011619 is listed at 80 kg packed, with a volume of 0.179 m3. That is a shipping figure for a crated unit, not the weight of the casting.

Our practice is to weigh the actual shipment and quote freight on that. If you need a weight for a forwarder quote before ordering, tell us the quantity and we will weigh a sample rather than repeat a number from a catalogue.

Laser Marking and Traceability

We laser mark housings on request, with the part number, a batch code and a two-dimensional code that resolves to the production record.

Laser-marked Cummins 4947472 flywheel housing showing part number and data matrix code

The marking in the photograph reads 4947472, a production code and a batch code, with the data matrix alongside. The value of this is not cosmetic. When a container arrives and a customer disputes what was shipped, the code on the casting answers the question without opening a claim.

If you want markings applied, send us the format you need, including whether the number should be the OEM number or your own internal reference. We can mark either.

What to Send Before You Order

Five items, and we can quote without coming back with questions.

  1. The engine nameplate, photographed, with the full model string and serial number.
  2. The SAE flange size at the gearbox end, if known, or the gearbox model so we can look it up.
  3. The PTO side: left, centre or right. For mixer, crane and refuse applications this decides the part.
  4. Whether the housing needs a machined sensor bore, and whether it needs timing marks.
  5. A photograph of the old housing from the rear face, with the cast numbers legible if possible.

Send these to Irene at [email protected] or WhatsApp +86 199 53662121 and we will confirm the number before quoting. Prices are FOB Qingdao unless you ask otherwise.

FAQ

Does 612600010305 fit WP10 or WD615

Both labels appear in the market, from three different suppliers, and we cannot settle it from the number alone. The casting may serve both generations. Confirm from the old housing’s flange and bore before ordering.

What does the digit after 6126000 mean

In the older twelve-digit Weichai system, 6126000 1 marks the housing and front-end group, including flywheel housings and timing gear housings. 6126000 2 marks the flywheel and driveline group. It is a functional grouping, not a sequential number.

Why do two Cummins numbers fit the same engine list

5253948 and 5253952 are both listed against the same 32 ISL9 and QSL9 engine models. They may differ in casting details that the listings do not show. We check the flange and PTO opening on the physical part rather than treating them as interchangeable.

Is 612600010018 an official Weichai number

It is cast into a centre-PTO housing we hold, with a date code and batch code beside it, so it is a genuine marking on the part. We have not found an independent catalogue entry for it and do not quote it as an official number on its own.

What is the weight of a Weichai flywheel housing

Published figures conflict badly. One page gives both 10.35 kg and 5.3 kg for 612600010012, and 612600011619 is listed at 80 kg packed in 0.179 m3. We weigh the actual shipment and quote freight on that.

Can you supply a housing with a specific PTO opening

Yes. Left, centre and right PTO castings are all in our range, and we hold samples of each. Tell us the application and the PTO side rather than the number alone.

Do you laser mark the housings

Yes, with the part number, batch code and a data matrix code on request. We can mark either the OEM number or your own internal reference.

What is the minimum order

One piece for a trial order, with price reducing from there. Terms are FOB Qingdao by default. Send the engine model, PTO side and quantity to [email protected] or +86 199 53662121.


Send the engine nameplate and a photograph of the old housing, and we will tell you which casting you actually need. Irene, [email protected], WhatsApp +86 199 53662121, or use the quotation form. Changwei International, FOB Qingdao.