Scania 1776466 Flywheel Part Number: 480 mm, 158 Teeth

Table of Contents
- Three Numbers On One Disc
- What The Catalogues Agree On
- Which Seller Lists Which Number
- What The Photos Show
- The Markings On The Rim
- Weight As A Receiving Check
- Where The Listings Conflict
- What To Send Before You Order
- Frequently Asked Questions
- Ordering This Flywheel
Three Numbers On One Disc
Search for a Scania 1776466 flywheel part number and you get three numbers back: 1776466, 573203 and 2481691. Some sellers print all three on one page. Others print two. One prints only the first.
That matters at the quotation stage. A buyer sends 2481691, the supplier quotes 1776466, and nobody is sure whether the two offers cover the same casting. The freight is quoted twice. The order stalls.

This page collects what five independent catalogues say about the disc we hold under 1776466. It separates what they agree on from what they do not. Every row below carries a source count, so you can see how thin the evidence is before you spend money on it.
What The Catalogues Agree On
Two catalogues publish full dimensions for 1776466. They were written by different companies, in different countries, and they agree on every number.
| Item | Published value | Sources |
|---|---|---|
| Outer diameter | 480 mm | Two, independent |
| Clutch mounting diameter | 430 mm | Two, independent |
| Ring gear teeth | 158 | Two, independent |
| Net weight | 46,380 g | Two, identical |
| Packed shipping weight | 47.78 kg | One |
| Our own stock label | 46.5 kg | Our record |
The 480 mm and the 430 mm are the two numbers a fitter checks first. The 480 mm is the outside of the toothed rim. The 430 mm is the circle the pressure plate bolts to. They are different circles on the same disc, and swapping them in a conversation is a common way to order the wrong part.
The net weight is the interesting row. Two catalogues state 46,380 g, to the gram. Our own stock label says 46.5 kg. That is a 120 g gap on a 46 kg part, which is the difference between a dry weight and a rounded one.
Which Seller Lists Which Number
The three numbers are not equally supported. This table is the honest version.
| Number | How many sellers list it | Listed by |
|---|---|---|
| 1776466 | Five | All five |
| 573203 | Three | Klotze, gztruck, Rokey |
| 2481691 | Two | gztruck, and a cross reference list at spareto |
So 1776466 is the anchor. 573203 has decent support. 2481691 is the weakest of the three, and it is also the number most often quoted by buyers in Asia, which is how mismatched offers happen.
Aftermarket brands also sell this disc under their own numbers. If your quotation comes back with one of these, it is not a different part.
| Brand | Own number |
|---|---|
| DT Spare Parts | 1.40000 |
| Klotze Technic | KT03125 |
| Yekpar | YS1.435 |
| Febi Bilstein | 178666 and 172697 |
| C.E.I. | 196.424 and 196.547 |
| Sampa | 043.246 |
| Auger | 81067 |
Two numbers from one brand, as Febi and C.E.I. both show, usually means two production versions or two clutch variants. Ask which one the quote covers.
What The Photos Show
We keep this disc in stock. The photos below are our own, taken on the packing table, not catalogue renderings.

The crank side is plain. There is no separate signal ring bolted to it, and no index dowel visible on the face. The bolt circle around the pilot bore carries eight large bores, with eight smaller bores between them. Outside that, a ring of small holes runs at the pressure plate radius.

From the side you can see the layering. The toothed band sits at the outer edge and is left dark. The rim beside it is machined bright, and the ring of holes crosses that bright band. The hub spigot stands proud of the disc on the crank side.

This angle is the one to copy when you photograph your own part for a supplier. It shows the tooth band, the rim holes and the hub spigot in a single frame. A flat face photo alone will not tell a supplier which of the Scania discs you have.

The teeth are cut square across the top, with a chamfer on the leading edge. That chamfer faces the starter. If you are replacing a ring gear rather than a whole disc, the chamfer orientation is the detail that decides whether the new gear grinds on the first crank.

The hub close-up is worth keeping. Eight large bores, eight small ones, and the pilot bore in the middle. Count them on the part in your hand before you accept a delivery. A disc with a different count is a different part, whatever the crate says.

At the edge, the friction face runs out to a machined step, then the tooth band begins. There is a single cast digit on the face in this view. We have not found a source that explains it, so we do not read anything into it.
The Markings On The Rim
The rim of our disc carries a stamped line that reads 24 01 18 3. It looks like a date: 24 January 2018, or 18 January 2024, depending on the order you read it.

It is a production code, not a part number. We have written about this before, because it is the single most common cause of a buyer concluding that a supplier shipped the wrong part: there is a number on the casting, it is not the number on the invoice, and nobody explains why. The full explanation of rim markings is in our guide to timing marks and date codes on a flywheel.
A short stamped word sits beside the date line on the same rim. We have photographed it at five times magnification and still cannot resolve it with confidence, so we are not going to print a reading here. It is not a part number either way.
What the rim does not carry is 1776466. That number lives in catalogues and on labels. If you are checking a delivery, check the label, the weight and the face geometry, not the rim.
Weight As A Receiving Check
A bathroom scale is the cheapest inspection tool in the warehouse. On this disc it is also a useful one.
Two catalogues say 46,380 g. Our label says 46.5 kg. A third seller lists 46.5 kg. The spread across all three is 120 g. That is tight enough to be a real check, not a guess.
| What you are weighing | Expected | Why it differs |
|---|---|---|
| Bare disc, dry | 46.38 to 46.5 kg | Rounding between catalogues |
| Disc in a crate, packed | about 47.8 kg | Crate and packing, roughly 1.3 kg |
| Disc with clutch bolted on | much higher | Not a comparable figure |
The trap is comparing a freight invoice against a net weight. A 47.8 kg shipping figure is not a 1.3 kg overweight part. It is the same disc plus its crate. We covered the wider version of this problem in our flywheel weight table by part number.
If your delivery weighs 44 kg, you do not have this disc. If it weighs 52 kg, you may have a different Scania number with the same tooth count. Both cases are worth a phone call before the gearbox comes out.
Where The Listings Conflict
Three conflicts are worth naming.
The first is the application list. One seller prints the fitment as “Mercedes Scania Bus 4-/F-/K-/N-Series” and then repeats Scania P/G/R/T on the next line. Mercedes does not build a Scania bus series. That line is machine generated and should not be used to confirm fitment.
The second is the weight. One seller states 46.5 kg, two state 46,380 g, and one lists a packed weight of 47.78 kg. Read together they are consistent. Read separately they look like three different parts.
The third is the one that costs money. Dimensions do not identify this disc. Our earlier page on Scania flywheel part numbers found four other Scania numbers at 158 teeth, 480 mm outside and 430 mm clutch. This one sits in the same envelope. If a supplier tells you “it is 480 and 158 teeth, so it fits”, that sentence proves nothing.
What To Send Before You Order
Four items settle it. None of them takes more than a few minutes.
| Send this | Why |
|---|---|
| The number from your old disc’s label, or the chassis number | The number decides the part, not the size |
| A photo of the crank side, flat on | Shows the bolt circle and whether a signal ring is present |
| A photo of the side profile, like the third photo above | Shows tooth band, rim holes and hub spigot together |
| The clutch diameter you are fitting | 430 mm for this disc, per two catalogues |
If the old disc is still on the engine, the chassis number is enough for us to check. If the engine is out and the label is gone, the two photos plus the weight will usually be enough to narrow it to one or two numbers.
Frequently Asked Questions
Is 2481691 the same flywheel as 1776466?
Two sources connect them, and neither is Scania’s own catalogue. One seller lists all three numbers on one product page. One European parts site lists 2481691 among the cross references for its 1776466 item. That is enough to treat them as likely interchangeable and not enough to promise it. Ask for both numbers to be quoted separately, then compare the weights.
Is 573203 a Scania number or a supplier number?
Three sellers print 573203 beside 1776466 as an OE reference. None of them explains what it is. We have not found a Scania document that settles it. Treat it as an interchangeable reference and confirm against the number on your old part.
What clutch size does this flywheel take?
430 mm, according to both catalogues that publish the clutch mounting diameter. The outer diameter is a separate figure at 480 mm. Do not quote 480 mm to a clutch supplier.
Will it fit my R-series?
The published applications cover Scania P, G, R and T series from 2003 to 2018, and L, P, G, R and S from 2016 onward. Those are catalogue statements, not our measurement. Send the chassis number and we will check it against the number before quoting.
How can I tell a 1776466 from the other 158 tooth Scania discs?
By weight and by the face, not by the tooth count. Weigh it: 46.4 to 46.5 kg is this disc. Then compare the crank side photo. The bolt circle and the ring of holes at the pressure plate radius are what differ between the numbers in this family. Counting teeth alone will not separate them.
Ordering This Flywheel
Send the number, the clutch diameter and one photo of the crank side. We will confirm the part before the quotation goes out, not after the crate lands.
We cast and machine flywheels in our own foundry in Changyi, Shandong, under IATF 16949. Ring gears are induction fitted and the assembly is balanced before packing. If you need the disc bare, say so. If you need it with the ring gear already pressed on, say that too, because the two are also sold separately. Our ring gear range covers the standalone part.
The disc in these photos is our production. It is identified as 1776466 from our stock record. The rim carries a date code, not the OE number, so the identification rests on the record and on the dimensions, and we have said so plainly rather than dressed it up.
Start here: request a quote.
Best regards,
Irene
Changwei International
Email: [email protected]
WhatsApp / WeChat: +86 199 5366 2121
Web: changweiintl.com